Page 41 / 101
Scroll up to view Page 36 - 40
39
Alternate Setup Method
section
1
9
2
3
4
5
6
7
8
10
Setting your ISP Connection Type to Static IP (IPoA)
This connection type is also called “Classical IP over ATM” or
“CLIP”, which your ISP provides a fixed IP for your Router to connect
to the Internet.
(1)
(2)
(3)
(4)
(5)
1.
WAN IP Address
- Enter an IP address assigned by your ISP for
the Router WAN interface.
2.
Subnet Mask
- Enter a subnet mask assigned by your ISP.
3.
Use Static Default Gateway
- Enter a default gateway IP address.
If the Router cannot find the destination address within its
local network, it will forward the packets to the default gateway
assigned by your ISP.
4.
VPI/VCI
- Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameter here. These identifiers are assigned by
your ISP.
5.
Encapsulation
- Select LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”.
Or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless your click “Apply Changes”.
Page 42 / 101
40
Alternate Setup Method
Setting your Connection Type to Modem Only (Disable
Internet Sharing)
In this mode, the Router simply acts as a bridge passing packets
across the DSL port. It requires additional software to be installed on
your computers in order to access the Internet.
(2)
(3)
1.
Enable Bridge Service
- Check this box to enable bridge service
2.
VPI/VCI
- Enter your Virtual Path Identifier (VPI) and Virtual Circuit
Identifier (VCI) parameters here. (Assigned by your ISP).
3.
Encapsulation
- Select the LLC or VC MUX your ISP uses.
Click “Apply Changes” to save and activate your settings. To go
back to the original settings before saving, click “Clear Changes”.
Or click any of the Quick-Navigation links for other options. Your
new settings will not be saved unless your click “Apply Changes”.
Page 43 / 101
41
Alternate Setup Method
section
1
9
2
3
4
5
6
7
8
10
Setting Custom Domain Name Server (DNS) Settings
A “Domain Name Server” is a server located on the Internet that
translates Universal Resource Locaters (URLs) like “www.belkin.
com” to IP addresses. Many Internet Service Providers (ISPs) do not
require you to enter this information into the Router. The “Automatic
from ISP” box
(1)
should be checked if your ISP did not give you a
specific DNS address. If you are using a static IP connection type,
then you may need to enter a specific DNS address and secondary
DNS address for your connection to work properly. If your connection
type is dynamic or PPPoE, it is likely that you do not have to enter a
DNS address. Leave the “Automatic from ISP” box checked. To enter
the DNS address settings, uncheck the “Automatic from ISP” box and
enter your DNS entries in the spaces provided. Click “Apply Changes”
(2)
to save the settings.
(1)
(2)
Page 44 / 101
42
Using the Web-Based Advanced User Interface
Using the Web-Based Advanced User Interface
Using your Internet browser, you can access the Router’s Web-Based
Advanced User Interface. In your browser, type “192.168.2.1” (do not
type in anything else such as “http://” or “www”) then press the
“Enter” key.
You will see the Router’s home page in your browser window.
Viewing the LAN Settings
Clicking on the header of the LAN tab
(1)
will take you to the LAN tab’s
header page. A quick description of the functions can be found here. To
view the settings or make changes to any of the LAN settings, click on
“LAN Settings”
(2)
or to view the list of connected computers, click on
“DHCP client list”
(3)
.
(1)
(2)
(3)
Page 45 / 101
43
Using the Web-Based Advanced User Interface
section
1
9
2
3
4
5
6
7
8
10
Changing LAN Settings
All settings for the internal LAN setup of the Router can be viewed
and changed here.
(1)
(2)
(4)
(5)
(6)
(3)
1.
IP Address
The “IP address” is the internal IP address of the Router. The
default IP address is “192.168.2.1”. To access the advanced setup
interface, type this IP address into the address bar of your browser.
This address can be changed if needed. To change the IP address,
type in the new IP address and click “Apply Changes”. The IP
address you choose should be a non-routable IP. Examples of a
non-routable IP are:
192.168.x.x (where x is anything between 0 and 255)
10.x.x.x (where x is anything between 0 and 255)
2.
Subnet Mask
There is no need to change the subnet mask. This is a unique,
advanced feature of your Belkin Router. It is possible to change
the subnet mask if necessary; however, do NOT make changes to
the subnet mask unless you have a specific reason to do so. The
default setting is “255.255.255.0”.
19216811.live