Page 11 / 105 Scroll up to view Page 6 - 10
9
G Wireless Router
SECTIONS
Table of Contents
1
2
4
5
6
7
8
9
10
3
KNOWING YOUR ROUTER
5� Internet LED
This unique LED shows you when the Router is connected to the
Internet� When the light is OFF, the Router is NOT connected to the
Internet� When the light is blinking, the Router is attempting to connect
to the Internet� When the light is solid GREEN, the Router is connected
to the Internet� When using the “Disconnect after x minutes” feature,
this LED becomes extremely useful in monitoring the status of your
Router’s connection�
OFF
Router is not connected to
the Internet
Blinking Green
Router is attempting to connect
to the Internet
Solid Green
Router is connected to
the Internet
6� Wired LEDs (1 – 2 – 3 – 4)
These LEDs are labeled 1–4 and correspond to the numbered ports on
the rear of the Router� When a computer is properly connected to one
of the wired computer ports on the rear of the Router, the LED will light�
GREEN means a 10/100Base-T device is connected� When information
is being sent over the port, the LED blinks rapidly�
OFF
No device is linked to the port
Solid Green
10/100Base-T device connected
Blinking Green
Port activity
(7)
(8)
(9)
Page 12 / 105
10
G Wireless Router
SECTIONS
Table of Contents
1
2
4
5
6
7
8
9
10
3
KNOWING YOUR ROUTER
7� Power Jack
Connect the included 9V DC power supply to this jack�
8� Connections to Computers (Wired Computer Ports) – Gray
Connect your wired (non-wireless) computers to these ports� These
ports are RJ45, 10/100 auto-negotiation, auto-uplinking ports for
standard UTP category 5 or 6 Ethernet cable� The ports are labeled 1
through 4� These ports correspond to the numbered LEDs on the front
of the Router�
9� Connection to Modem (Modem Port) – Yellow
This port is for connection to your cable or DSL modem� Use the cable
that was provided with the Router to connect the modem to this port�
Use of a cable other than the cable supplied with the Router may not
work properly�
10� Reset Button
The “Reset” button is used in rare cases when the Router may function
improperly� Resetting the Router will restore the Router’s normal
operation while maintaining the programmed settings� You can also
restore the factory default settings by using the “Reset” button� Use
the restore option in instances where you may have forgotten your
custom password�
a� Resetting the Router
Push and release the “Reset” button� The lights on the Router will
momentarily flash� The reset is complete in 60 seconds�
b� Restoring the Factory Defaults
Press and hold the “Reset” button for at least 10 seconds, then release
it� The lights on the Router will momentarily flash� The restore is
complete in 60 seconds�
Page 13 / 105
11
G Wireless Router
SECTIONS
Table of Contents
1
2
3
5
6
7
8
9
10
CONNECTING AND CONFIGURING YOUR ROUTER
4
Verify the contents of your box� You should have the following:
Belkin G Wireless Router
Quick Installation Guide
Belkin Setup Assistant Software CD with User Manual
RJ45 Ethernet Networking Cable (for connection of the Router to
the modem)
Power Supply
Modem Requirements
Your cable or DSL modem must be equipped with an RJ45 Ethernet
port� Many modems have both an RJ45 Ethernet port and a USB
connection� If you have a modem with both Ethernet and USB, and are
using the USB connection at this time, you will be instructed to use the
RJ45 Ethernet port during the installation procedure� If your modem has
only a USB port, you can request a different type of modem from your
ISP, or you can, in some cases, purchase a modem that has an RJ45
Ethernet port on it�
Setup Assistant
Belkin has provided our Setup Assistant software to make installing your
Router a simple and easy task� You can use it to get your Router up and
running in minutes� The Setup Assistant requires that your Windows
2000/XP, Vista, or Mac OS X v10�4 or v10�5 computer be connected
directly to your cable or DSL modem and that the Internet connection is
active and working
at the time of installation� If it is not, you must use
the “Alternate Setup Method” section of this User Manual to configure
your Router� Additionally, if you are using an operating system other
than Windows 2000/XP, Vista, or Mac OS X v10�4 or v10�5, you must
set up the Router using the “Alternate Setup Method” section of this
User Manual�
ALWAYS INSTALL YOUR ROUTER FIRST!
If you are installing
numerous network devices for the first time, it is important that your
Router is connected and running before attempting to install other
network components such as notebook cards and desktop cards�
Page 14 / 105
12
G Wireless Router
SECTIONS
Table of Contents
1
2
3
5
6
7
8
9
10
4
CONNECTING AND CONFIGURING YOUR ROUTER
Step 1: Hardware Connections
A�
Unplug your modem’s power cord� Put the Router next to the
modem� Raise the Router’s antenna�
B�
Locate the networking cable that connects your modem and
computer� Unplug that cable from your modem, and plug it into any
gray port on the back of the Router�
C�
Find your new networking cable (included in the box with your
Router) and connect it to the yellow port on the back of the Router�
Connect the other end to your modem, in the port that’s now free�
D�
Plug in your modem’s power cord� Wait 60 seconds for the modem
to start up� Plug the Router’s power supply into the black port on
the back� Plug the other end into the wall outlet�
E�
Wait 20 seconds for the
Router to start up� Look
at the display on the front
of the Router� Make sure
the “Wired” and “Power”
icons are lit up in green�
If they are not, recheck
your connections�
LAN
WAN
B
D
D
A
D
C
C
A
Page 15 / 105
13
G Wireless Router
SECTIONS
Table of Contents
1
2
3
5
6
7
8
9
10
4
CONNECTING AND CONFIGURING YOUR ROUTER
Note for Windows Users:
If the Setup Assistant does not start
up automatically, select your CD-ROM drive from “My Computer”
and double-click on the file named “SetupAssistant” to start the
Setup Assistant�
Step 2: Set Up the Router – Run the Setup Assistant Software
A�
Shut down any programs that are running on your computer at this
time� Turn off any firewall or Internet-connection-sharing software
on your computer�
B�
Insert the CD into your computer� The Setup Assistant will
automatically appear on your computer’s screen within 15
seconds� Click on “Go” to run the Setup Assistant� Follow the
instructions there�
IMPORTANT:
Run the Setup Assistant from the computer that is
directly connected to the Router from Step 1�B�

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top