1. Home
    2. /
  2. Manuals
    3. /
  3. Belkin
    4. /
  4. F5D7231-4v5
    5. /
  5. 10
Page 46 / 133 Scroll up to view Page 41 - 45
44
Using the Web-Based Advanced User Interface
Configuring the Wireless Network Settings
The Wireless tab lets you make changes to the wireless network
settings. From this tab you can make changes to the wireless network
name (SSID), operating channel, encryption security settings, and
configure the Router to be used as an access point.
Changing the Wireless Network Name (SSID)
To identify your wireless network, a name called the SSID (Service
Set Identifier) is used. The default SSID of the Router is “belkin54g”.
You can change this to anything you want to or you can leave it
unchanged. If there are other wireless networks operating in your
area, you will want to make sure that your SSID is unique (does not
match that of another wireless network in the area). To change the
SSID, type in the SSID that you want to use in the SSID field
(1)
and
click “Apply Changes”
(2)
. The change is immediate. If you make a
change to the SSID, your wireless-equipped computers may also need
to be reconfigured to connect to your new network name. Refer to the
documentation of your wireless network adapter for information on
making this change.
(1)
(2)
Downloaded from
www.Manualslib.com
manuals search engine
Page 47 / 133
Using the Web-Based Advanced User Interface
45
section
2
1
3
4
5
6
7
8
9
10
11
12
Using the Wireless Mode Switch
Your Router can operate in three different wireless modes: “802.11g-
Auto”, “802.11g-Only”, and “802.11g-LRS”. The different modes are
explained below.
802.11g-Auto Mode
In this mode, the Router is compatible with 802.11b and 802.11g
wireless clients simultaneously. This is the factory default mode and
ensures successful operation with all Wi-Fi-compatible devices. If
you have a mix of 802.11b and 802.11g clients in your network, we
recommend setting the Router to 802.11g-Auto mode. This setting
should only be changed if you have a specific reason to do so.
802.11g-Only Mode
802.11g-Only mode works with 802.11g clients only. This mode
is recommended only if you want to prevent 802.11b clients from
accessing your network. To switch modes, select the desired
mode from the “Wireless Mode” drop-down box. Then, click
“Apply Changes”.
802.11g-LRS Mode
We recommend you DO NOT use this mode unless you have a very
specific reason to do so. This mode exists only to solve unique
problems that may occur with some 802.11b client adapters and is
NOT necessary for interoperability of 802.11g and 802.11b standards.
When to Use 802.11g-LRS Mode
In some cases, older 802.11b clients may not be compatible with
802.11g wireless. These adapters tend to be of inferior design and
may use older drivers or technology. 802.11g-LRS (Limited Rate
Support) allows these clients to be compatible with the newer
802.11g technology. Switching to this mode can solve problems that
sometimes occur with these clients. If you suspect that you are using
a client adapter that falls into this category of adapters, first check
with the adapter vendor to see if there is a driver update. If there
is no driver update available, switching to 802.11g-LRS mode may
fix your problem.
Please note that switching to 802.11g-LRS mode may
decrease 802.11g performance slightly
.
Downloaded from
www.Manualslib.com
manuals search engine
Page 48 / 133
46
Using the Web-Based Advanced User Interface
Using High-Speed Mode
The Router supports two High-Speed modes, 125HSM* mode and
Frame Bursting mode.
Selecting “125HSM mode” will result in all devices running in 125HSM
mode if all devices are capable of 125Mbps speeds. If any
non-125HSM device connects or associates with the network, the
Router will automatically shift the entire network back to Frame
Bursting mode.
Selecting “Frame Bursting” will result in all devices capable of
Frame Bursting to function in Frame Bursting mode, and all clients
not capable, to operate in normal 802.11g modes. Frame Bursting
mode supports both Frame Bursting-enabled devices and non-Frame
Bursting-enabled devices simultaneously. Frame Bursting mode is
based on the unreleased 802.11e specification.
Selecting “Off” will disable Turbo mode.
*When operating in High-Speed Mode, this Wi-Fi device may achieve an actual throughput
of up to or greater than 34.1Mbps, which is the equivalent throughput of a system following
802.11g protocol and operating at a signaling rate of 125Mbps. Actual throughput will vary
depending on environmental operational and other factors.
Downloaded from
www.Manualslib.com
manuals search engine
Page 49 / 133
Using the Web-Based Advanced User Interface
47
section
2
1
3
4
5
6
7
8
9
10
11
12
Changing the Wireless Channel
There are a number of operating channels you can choose from. In
the United States and Australia, there are 11 channels. In the United
Kingdom and most of Europe, there are 13 channels. In a small
number of other countries, there are other channel requirements.
Your Router is configured to operate on the proper channels for
the country you reside in. The default channel is 11 (unless you are
in a country that does not allow channel 11). The channel can be
changed if needed. If there are other wireless networks operating in
your area, your network should be set to operate on a channel that is
different than the other wireless networks. For best performance, use
a channel that is at least five channels away from the other wireless
network. For instance, if another network is operating on channel 11,
then set your network to channel 6 or below. To change the channel,
select the channel from the drop-down list. Click “Apply Changes”.
The change is immediate.
Downloaded from
www.Manualslib.com
manuals search engine
Page 50 / 133
48
Using the Web-Based Advanced User Interface
Using the Broadcast SSID Feature
Note: This advanced feature should be employed by advanced users only.
For security, you can choose not to broadcast your network’s SSID.
Doing so will keep your network name hidden from computers that
are scanning for the presence of wireless networks. To turn off the
broadcast of the SSID, remove the check mark from the box next to
“Broadcast SSID”, and then click “Apply Changes”. The change is
immediate. Each computer now needs to be set to connect to your
specific SSID; an SSID of “ANY” will no longer be accepted. Refer to
the documentation of your wireless network adapter for information
on making this change.
Protected Mode Switch
As part of the 802.11g specification, Protected Mode ensures proper
operation of 802.11g clients and access points when there is heavy
802.11b traffic in the operating environment. When Protected mode
is ON, 802.11g scans for other wireless network traffic before it
transmits data. Therefore, using this mode in environments with
HEAVY 802.11b traffic or interference achieves best performance
results. If you are in an environment with very little—or no—other
wireless network traffic, your best performance will be achieved with
Protected mode OFF.
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular Belkin Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top