Page 6 / 71 Scroll up to view Page 1 - 5
Page 3
The ‘Charge’ port on your router is dedicated to
charging USB powered devices, such as mobile phones,
iPods, etc. The charge port will supply a maximum 5V
500mA. Connecting a USB device which requires more
than 500mA may result in damage to your equipment.
QoS
QoS (Quality of Service) limits the traffic being sent
from the router (upstream) when using VoIP at the
same time. If QoS is disabled, the quality of the VoIP
call can suffer due to excessive traffic from another
source, such as a PC. When QoS is enabled, it limits the
upstream traffic and sets it aside for VoIP, increasing
the call quality.
Virtual Server
If you have a fixed IP address, you can set the router
to act as a virtual host for network address translation.
Remote users access various services at your site
using a constant IP address. Then, depending on
the requested service (or port number), the router
can route the request to the appropriate server (at
another internal IP address).This secures your network
from direct attack by hackers, and provides more
f lexible management by allowing you to change
internal IP addresses without affecting outside access
to your network.
Support for VPN Pass-Through
If you connect to your office network from home using
a VPN connection, your router will allow your VPN-
equipped computer to pass through the router and to
your office network. This router supports 1 VPN session
at any one time
This router supports three of the most commonly
used VPN protocols – PPTP, L2TP, and IPSec. The
VPN protocols supported by the router are brief ly
described below.
Point-to-Point Tunneling Protocol – Provides a
secure tunnel for remote client access to a PPTP
security gateway. PPTP includes provisions for call
origination and flow control required by ISPs.
L2TP merges the best features of PPTP and L2F
– Like PPTP, L2TP requires that the ISP’s routers
support the protocol.
IP Security – Provides IP network-layer encryption.
IPSec can support large encryption networks (such
as the Internet) by using digital certificates for device
authentication.
Wired & Wireless LAN
The router provides access for up to 4 by 10/100 Mbps
wired devices and up to an additional 32 wireless
devices, making it easy to create a network in small
offices or homes. 802 11b, 802 11g & 802 11n wireless
standards are supported.
MAC Address Filtering
For added security, you can set up a list of MAC
addresses (unique client identifiers) that are allowed
access to your network
Every computer has its own
MAC address. Simply enter these MAC addresses into
a list using the web-based user interface and you can
control access to your network.
WEP, WPA and WPA 2 Encryption
protocols
The router features WPA2, which is the second
generation of the WPA-based 802 11i
standard. It
offers a higher level of wireless security by combining
advanced network authentication and stronger
Advanced Encryption Standard (AES) encryption
methods. It also supports the legacy security standard
called Wired Equivalent Privacy (WEP) in order to allow
you to activate security with any legacy devices you
may have on your network.
VLAN
VLAN (Virtual Local Area Network) adds the ability to
manage multiple networks with the one router. The
router is designed to be placed on a desktop. All of
the cables exit from the rear of the router for better
organisation and utility. The LED indicators are easily
visible on the front of the router to provide you with
information about network activity and status.
BoB
TM
Handset
The BoB
TM
handset is an optional device which slots
into the front of the BoB
TM
router and allows you to
make voice calls (including VoIP where available).
The BoB
TM
router can support up to 5 DECT-compatible
handsets and the handset cradle also functions as a
charger for the BoB
TM
handset when it is not in use.
Chapter 2 :
Product Overview
About BoB
TM
4 port integrated wireless router
Page 7 / 71
Page 4
LED indicators are easily visible on the front of the
router to provide you with information about network
activity and status. All cables and connections
conveniently exit from the rear of the router.
Front Panel
Power LED
When you apply power to the router or restart it, a
short period of time elapses while the router boots
up. When the router has completely booted up,
the Power LED becomes a SOLID light, indicating
the router is ready for use.
Off
- Router is off
Orange
- Router is booting
Blue
- Router is on and ready for use
ADSL SYNC LED
The ADSL LED will light up yellow indicating no ADSL
sync. Once line sync is established the LED will light
up blue.
Off
- No ADSL connection
Orange
- Negotiating connection/No ADSL
sync
On
- ADSL link is up and connected
1.
2.
Internet LED
The Internet LED shows you when the router
is connected to the Internet. If the LED is off
or yellow the router is NOT connected to the
Internet.
Off
– Not connected to Internet
Orange
– The router is not connected
to the internet or a problem
has been detected.
On
– Connected to internet
LAN Status LED
When a computer is properly connected to the
LAN port on the rear of the router, the LED shown
here will light. A solid light means a computer or
a network-enabled device is connected. When
information is being sent over the port, the LED
blinks rapidly.
Off
- Your computer is not connected
On
- Your computer is connected
Wireless Status LED
The Wireless status LED shows you when the
router’s wireless is enabled.
On
- Wireless enabled
Orange
- Solid, the router has detected a
problem with a client connecting
to the wireless
Off
- Wireless is disabled
6 & 7. Phone Status LED 1-2
The phone lights indicate whether VoIP account
one or two has successfully registered on the
network.
On
- VoIP registered successfully
Orange
- Solid, the router has detected a
problem registering your VoIP
account on the network
Off
- No VoIP activity
Storage/3g
When a USB mass storage device is connected
to this USB Port, this light will illuminate to inform
you the attached storage device is ready for use.
This USB port also accepts a 3g wireless modem
service.
On
– Attached USB Mass Storage or
3g Device connected and ready
for use
Off
– No attached USB Mass Storage
or 3g Device
3.
4.
5.
8.
Note
on Side Panel Ports:
The router has an
aforementioned USB/3g
port labelled ‘3g/storage’
along with a USB charge
port.
The charge port is able
to charge devices which
use a USB connection,
such as iPods, etc.
Chapter 3 :
Knowing BoB
TM
Knowing your BoB
TM
- 4 port integrated wireless router
Page 8 / 71
Page 5
Back Panel
Chapter 4 :
Connection & Configuration
Connect & Configure
your BoB
TM
Power Switch
The power switch allows you to switch on or off
the router. Once you have connected the power
plug, f lip the switch to ON (‘1’) to power on the
router.
Power Plug
Connect the included 12V 1 5A DC power supply to
this inlet. Using the wrong type of power adapter
may cause damage to your router.
Reset Button
Resetting the Router
Push and hold the Reset button for one second
then release it. When the power light becomes
solid again the reset is complete.
Restoring the Factory Defaults
Push and hold the Reset button for ten seconds
then release it. When the power light becomes
solid again the restore is complete.
LAN Ports
The Ethernet port is RJ45, 10/100 auto-negotiation.
Connect your net work-enabled computers or any
networking devices to this port.
Phone Two Port
Phone Port connects to standard analogue
telephone set or fax machine.
PSTN Failover Port
The Optional RJ-11 port is for connection to your
PSTN (Home Phone) line to provide Normal Phone
call backup for when VoIP is unavailable or not
required.
1.
2.
3.
4.
5.
6.
ADSL Line
This port is for connection to your ADSL line
Connect your ADSL line to this port.
Locate handset (if
installed)
Press this button to signal the BoB
TM
handset to
ring, allowing you to easily find its current location
Useful if you have lost the handset.
Register additional handsets
Allows you to register additional DECT compliant
handsets to your router. A total of 5 DECT
handsets can be registered to your router at any
one time.
7.
8.
9.
Page 9 / 71
Page 6
Step 1. Find a suitable location
Your BoB
TM
- 4 port integrated wireless router can be
positioned at any convenient location in your office
or home where there is easy access to a phone jack
and power point nearby. No special wiring or cooling
requirements are needed and there is no necessity to
keep the unit connected directly to a computer.
You should, however, comply with the following
guidelines:
Keep the router away from any heating devices
Do not place the router in a dusty or wet
environment
You should also remember to turn off the power,
remove the power cord from the outlet, and keep
your hands dry when you install the router.
Step 2. Connect the ADSL Line
Phone line configuration
Run a standard telephone cable from the wall jack
providing ADSL service to the RJ-11 (‘ADSL’) port on
your router. When inserting an ADSL RJ-11 plug, be
sure the tab on the plug clicks into position to ensure
that it is properly seated. If you are using a splitter
less ADSL service, be sure you add low-pass filters
between the ADSL wall jack and your telephones
(these filters pass voice signals through but filter data
signals out).
If more than 4 connections of any kind (i e faxes,
phones, modems etc) are to be used you will need to
get a central splitter.
Step 3. Attach to your network
using Ethernet cabling
The LAN ports on the router auto-negotiates the
connection speed to 10 Mbps Ethernet or 100 Mbps
Fast Ethernet, as well as the transmission mode to
half duplex or full duplex.
Use twisted-pair cabling to connect any of the LAN
ports on the router to an Ethernet adapter on your
PC. Otherwise, cascade the LAN port on the router
to an Ethernet hub or switch, and then connect your
PC or other network equipment to the hub or switch.
When inserting an RJ-45 connector, be sure the tab
on the connector clicks into position to ensure that it
is properly seated.
Warning: Do not plug a phone jack connector into an
RJ-45 port. This may damage the router. Instead, use
only twisted-pair cables with RJ-45 connectors that
conform to Australian standards.
Step 4. Connect the power
adapter
Plug the power adapter into the power socket on
the rear panel of the router, and the other end into a
power outlet.
Check the power indicator on the front panel
is lit. If the power indicator is not lit, refer to
‘Troubleshooting’.
In case of a power failure, the router will automatically
restart and begin to operate once the power is
restored.
At this time we have now completed connecting the
router and may now move to the actual configuration
of your connection.
*Time needed to obtain line sync will vary depending
on various factors such as line noise and attempted
sync speed.
Notes:
Use 100-ohm shielded
or unshielded twisted-
pair cable with RJ-45
connectors for all
Ethernet ports. Use
Category 3, 4, or 5
for connections that
operate at 10 Mbps,
and Category 5 for
connections that
operate at 100 Mbps.
Chapter 4 :
Connection & Configuration
Connect & Configure
your BoB
TM
Page 10 / 71
Page 7
Step 1. How to log into the router
After you have configured TCP/IP on a client
computer, use a web browser to configure the router.
The router can be configured by any Java-supported
browser such as Internet Explorer 5.0 or above. Using
the web management interface, you may configure
the router and view statistics to monitor network.
To access the router’s management interface, enter
the IP address of the router in your web browser: 10.1.1.1
Note: If you are unable to access this web
page please look at the IP setup section of the
Troubleshooting section at the back of this manual.
Type in ‘admin’ as the password and click login. NOTE:
Password is case sensitive.
ISP Settings
Please collect the following information from your ISP
before setting up the router:
ISP account user name and password
Protocol, encapsulation and VPI/VCI circuit numbers
DNS server address
IP address, subnet mask and default gateway (for
fixed IP users only)
Step 2. Navigating the web
browser interface ISP account user
name and password
The router’s management interface consists of a
Setup Wizard and an Advanced Setup section.
Setup Wizard: Use the Setup Wizard to quickly set up
the router.
Advanced Setup: Advanced Setup supports more
advanced functions like hacker attack detection, IP
and MAC address filtering, virtual server setup, virtual
DMZ host, as well as other functions.
Note: If you would like to add any additional functions
to your router please view the Advanced Setup
table of contents in order to find the correct setup
method.
Making Configuration Changes
Configurable parameters have a dialog box or a drop-
down list. Once a configuration change has been
made on a page, most of the times you will need
to click the ‘SAVE SETTINGS’ or ‘NEXT’ button at the
bottom of the page to enable the new setting unless
there is an ‘ADD’ button for instance.
Note: To ensure proper screen refresh after a
command entry, be sure that Internet Explorer 5.0
and above is configured as follows: Under the menu
Tools/Internet Options/General/Temporary Internet
Files/Settings, the setting for ‘Check for newer
versions of stored pages’ should be ‘Every visit to the
page.’
Chapter 5 :
Advanced Setup
BoB
TM
Advanced Setup Method

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top