Page 81 / 146 Scroll up to view Page 76 - 80
Chapter 4: Configuration
77
PPTP Connection - Remote Access
Connection Name:
A user-defined name for the connection (e.g. “connection to office”).
Type:
Check
Dial Out
if you want your router to operate as a client (connecting to a remote VPN
server, e.g. your office server), check
Dial In
operates as a VPN server.
~
When configuring your router as a Client, enter the remote
Server IP
Address
(or Domain
Name)
you wish to connection to.
~
When configuring your router as a server, enter the
Private IP Address Assigned to Dial
in User
address.
Username:
If you are a Dial-Out user (client), enter the username provided by your Host.
If you
are a Dial-In user (server), enter your own username.
Password:
If you are a Dial-Out user (client), enter the password provided by your Host.
If you
are a Dial-In user (server), enter your own password.
PPP Authentication Type:
Default is
Auto
if you want the router to determine the authentication
type to use, or else manually specify CHAP (Challenge Handshake Authentication Protocol) or
PAP (Password Authentication Protocol) if you know which type the server is using (when acting
as a client), or else the authentication type you want clients connecting to you to use (when acting
as a server). When using PAP, the password is sent unencrypted, whilst CHAP encrypts the
password before sending, and also allows for challenges at different periods to ensure that an
intruder has not replaced the client.
Data Encryption:
Data sent over the VPN connection can be encrypted by an MPPE algorithm.
Default is
Auto,
so that this setting is negotiated when establishing a connection, or else you can
manually
Enable
or
Disable
encryption.
Key Length:
The data can be encrypted by MPPE algorithm with 40 bits or 128 bits. Default is
Auto
, it is negotiated when establishing a connection. 128 bit keys provide stronger encryption
than 40 bit keys.
Mode:
You may select
Stateful
or
Stateless
mode. The key will be changed every 256 packets
when you select Stateful mode. If you select Stateless mode, the key will be changed in each
packet.
Page 82 / 146
Chapter 4: Configuration
78
Idle Time
: Auto-disconnect the VPN connection when there is no activity on the connection for a
predetermined period of time. 0 means this connection is always on.
Active as default route
: Enables the default route.
Click
Apply
button to apply your changes.
Page 83 / 146
Chapter 4: Configuration
79
PPTP Connection - LAN to LAN
Connection Name:
A user-define description of the connection.
Type:
Check
Dial Out
if you want your router to operate as a client (connecting to a remote VPN
server, e.g. your office server), check
Dial In
operates as a VPN server.
~
When configuring your router as a Client, enter the remote
Server IP
Address
(or
Hostname)
you wish to connection to.
~
When configuring your router as a server, enter the
Private IP Address Assigned to Dial
in User
address.
Peer Network IP:
Enter Peer network IP address.
Netmask:
Enter the subnet mask of peer network based on the Peer Network IP setting.
Username:
If you are a Dial-Out user (client), enter the username provided by your Host.
If you
are a Dial-In user (server), enter your own username.
Password:
If you are a Dial-Out user (client), enter the password provided by the your Host. If you
are a Dial-In user (server), enter your own password.
PPP Authentication Type:
Default is
Auto
if you want the router to determine the authentication
type to use, or else manually specify CHAP (Challenge Handshake Authentication Protocol) or
PAP (Password Authentication Protocol) if you know which type the server is using (when acting
as a client), or else the authentication type you want clients connecting to you to use (when acting
as a server). When using PAP, the password is sent unencrypted, whilst CHAP encrypts the
password before sending, and also allows for challenges at different periods to ensure that the
client has not been replaced by an intruder.
Data Encryption:
Data sent over the VPN connection can be encrypted by an MPPE algorithm.
Default is
Auto,
so that this setting is negotiated when establishing a connection, or else you can
manually
Enable
or
Disable
encryption.
Key Length:
The data can be encrypted by MPPE algorithm with 40 bits or 128 bits. Default is
Auto
, it is negotiated when establishing a connection. 128 bit keys provide stronger encryption
than 40 bit keys.
Page 84 / 146
Chapter 4: Configuration
80
Mode:
You may select
Stateful
or
Stateless
mode. The key will be changed every 256 packets
when you select Stateful mode. If you select Stateless mode, the key will be changed in each
packet.
Idle Time
: Auto-disconnect the VPN connection when there is no activity on the connection for a
predetermined period of time. 0 means this connection is always on.
Click
Apply
button to apply your changes.
Page 85 / 146
Chapter 4: Configuration
81
IPSec (IP Security Protocol)
Click
Create
to create a new IPSec VPN connection account.
After you have created the IPSec connection, account information will be displayed. (See example
above).
~
Enable / Disable:
This function activates or deactivates the IPSec connection.
To wish
interrupting the tunnel, check
Disable
radio button and click
Apply
button to deactivate the
connection.
Name:
This is the user-defined name of the connection.
Local Subnet:
Displays IP address and subnet of the local network.
Remote Subnet:
Displays IP address and subnet of the remote network.
Remote Gateway:
This is the IP address or Domain Name of the remote VPN device that is
connected and established a VPN tunnel.
IPSec Proposal:
This is selected IPSec security method.

Rate

4.5 / 5 based on 2 votes.

Popular BEC Technologies Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top