1. Home
    2. /
  2. Manuals
    3. /
  3. Baytec
    4. /
  4. RTA04N
    5. /
  5. 6
Page 26 / 78 Scroll up to view Page 21 - 25
RTA04N User
’
s Manual
Ed.0.1
Page 26 of 78
Figure 4-8
LAN IP Address:
Displays the LAN IP address of the Modem Router
Subnet Mask:
Displays the subnet mask of the Modem Router.
DHCP Mode:
Options available are
None
,
DHCP Relay
and
DHCP Server
.
1)
None:
In this mode, the Modem Router will do nothing when the host requests an IP address
by DHCP protocol. The screen will be shown as in Figure 4-9.
Figure 4-9
Page 27 / 78
RTA04N User
’
s Manual
Ed.0.1
Page 27 of 78
2)
DHCP Relay:
In this mode, the Router will work as a DHCP Relay. A DHCP relay is a device
that forwards DHCP data between computers that request IP addresses and the DHCP server
that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay.
In this mode, the DHCP requests from local PCs will be forwarded to the DHCP server running
on WAN side.
Figure 4-10
Relay Server:
Enter the IP Address of the DHCP server running on WAN side.
3)
DHCP Server:
Select this mode, then the screen will be shown as in Figure 4-11. The Router
will work as a DHCP Server; it becomes the default gateway for DHCP client connected to it.
That device on your local network must be set as a DHCP client to obtain the IP address
automatically. By default, the DHCP Server is enabled.
Figure 4-11
Page 28 / 78
RTA04N User
’
s Manual
Ed.0.1
Page 28 of 78
IP Pool Range:
Specify the start and end IP address for the DHCP server's IP
assignment. The default start and end IP Address are 192.168.1.100 and 192.168.1.200
separately. Please note that both addresses should be smaller than 192.168.1.254.
Default Gateway:
The default gateway address.
Max Lease Time:
The time that the DHCP client is allowed to maintain the assigned
dynamic IP. After the dynamic IP address has expired, the user will be automatically
assigned a new one. The default is
1440
minutes.
Domain Name:
Specify a user-friendly name to refer to the group of hosts (subnet) that
will be assigned addresses from this pool.
DNS Servers:
The IP address of DNS server used in option filed of DHCP message.
Apply Changes:
Click this button to save your configuration.
Undo:
Click this button to cancel your configuration.
Set VendorClass IP Range:
Click this button and then you will enter the screen as shown in
Figure 4-12
. This page allows you to configure the IP address range depending on device’s
option60.
Figure 4-12
Device name:
Give a name for the class of your device, such as PC, Phone, TV, etc.
Start address:
Specify the start address.
End address:
Specify the end address.
Default gateway:
Enter the IP address of the Modem Router.
Page 29 / 78
RTA04N User
’
s Manual
Ed.0.1
Page 29 of 78
Option60:
A string of n octets, interpreted by DHCP servers, used by DHCP client to
optionally identify the vendor type and configuration of a DHCP client. In Figure 4-12, we
suppose 11 as PC’s option60.
After configuration, click
Apply Changes
button to save your changes.
Note:
After configuration, you need to click the
Save
button appeared on the left panel so that your
configuration can still take effect after the Router reboots.
4.2.2.3. DHCP Static
Choose “
Setup→LAN→DHCP Static
” menu, you can view and add a static address for client via
the next screen (shown in Figure 4-13). When you specify a static IP address for a PC on the LAN,
that PC will always receive the same IP address each time when it accesses the DHCP server.
Static IP address is recommended to be assigned to the client that requires permanent IP settings.
Figure 4-13
IP Address:
Enter the IP address desired to be assigned to the client.
Mac Address:
Enter the MAC address of the client.
Add:
Click this button to add a new static IP entry.
Delete Selected:
Click this button to delete the selected entry in the DHCP Static IP Table.
Undo:
Click this button to delete your entering.
Note:
After configuration, you need to click the
Save
button appeared on the left panel so that your
configuration can still take effect after the Router reboots.
Page 30 / 78
RTA04N User
’
s Manual
Ed.0.1
Page 30 of 78
4.2.3.
WLAN
There are six submenus under the WLAN menu, Basic, Security, Access Control, Advanced, WPS,
and WDS. Click any of them, and you will be able to configure the corresponding function.
4.2.3.1. Basic
Choose “
Setup→WLAN→Basic
” menu, and you will see the Wireless Basic Settings screen (shown
in Figure 4-14). Please configure the parameters for wireless according to the descriptions below.
Figure 4-14
Disable Wireless LAN Interface:
Choose to disable the Wireless function of the ADSL Router.
Band:
Options available are 2.4 GHz (B), 2.4 GHz (G), 2.4 GHz (B+G), 2.4 GHz (N), 2.4 GHz
(G+N), and 2.4 GHz (B+G+N).
Mode:
Options are AP and AP+WDS. If AP+WDS is selected, then the Router can bridge two
or more WLANs.
SSID:
Wireless network name shared among all points in a wireless network. The SSID must
be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32
characters (use any of the characters on the keyboard). Make sure this setting is the same for
all stations in your wireless network. Type the desired SSID in the space provided.
Channel Width:
Select the width you want to use from the drop-down List. There are three
options, 20MHz, 40MHZ and 20/40MHz. If bigger bandwidth is selected, device could transmit
and receive data with higher speed.
Control Sideband:
Options are Upper and Lower.

Rate

4.3 / 5 based on 3 votes.

Popular Baytec Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top