1. Home
    2. /
  2. Manuals
    3. /
  3. Aztech
    4. /
  4. DSL1000EW-L
    5. /
  5. 8
Page 36 / 50 Scroll up to view Page 31 - 35
User Manual
Page 36
of 50
As an example, to setup an ftp server on a computer using 192.168.1.2 as its IP Address,
select FTP as Service and enter 192.168.1.2 as the Server IP Address. Otherwise if the
service you want to setup is not available from the Select a Service drop-down list, you
can define your own Port Forwarding rule.
DMZ Host
If a computer is assigned as a DMZ Host, it will receive all the data from the Internet that
do not belong to the list of applications configured in Port Forwarding. Enter the LAN IP
address of the PC you wish to set as DMZ Host in the provided box. If you need to disable
the DMZ Host, just click the remove button.
Note:
Note:
Note:
Note: DMZ exposes your computer to the Internet and will be vulnerable to malicious
attacks.
Port Triggering
Some applications require that the specific ports in the router’s firewall be opened for
access by the remote parties. A maximum of 8 entries can be configured.
Page 37 / 50
User Manual
Page 37
of 50
To setup Port Triggering:
For instance, an application uses port 25 for requests and port 113 for replies. If a
computer on the LAN connects to port 25 on a remote server hosting this application,
using Port Triggering on the router, incoming connections to port 113 (from the remote
server) could be redirected to the PC which initiated the request.
DDNS
The router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign
a fixed host and domain name to a dynamic Internet IP Address. It is useful when you
are hosting your own website, FTP server, or other server behind the router.
Before using this feature, you need to sign up for DDNS service providers.
Using DynDNS.org
Key in the following parameters:
Service provider
Service provider
Service provider
Service provider Select www.DynDNS.org.
My Hostname
My Hostname
My Hostname
My Hostname Enter the hostname.
DynDNS Settings
DynDNS Settings
DynDNS Settings
DynDNS Settings Enter your dyndns.org Username and password.
Page 38 / 50
User Manual
Page 38
of 50
Route
If your LAN consists of multiple subnets and you want to manually define the data
transmitting paths, Static Route is to be used.
The key settings for adding a new Static Route are explained:
Destination Network Address
Destination Network Address
Destination Network Address
Destination Network Address Enter the network address to which the data packets
are to be sent.
Subnet Mask
Subnet Mask
Subnet Mask
Subnet Mask Enter the subnet mask for this destination.
Use
Gateway
IP
Address
Use
Gateway
IP
Address
Use
Gateway
IP
Address
Use Gateway IP Address If you wish to use a specific gateway to reach the
destination network, select this checkbox and then enter the IP address of the
gateway.
Use Interface
Use Interface
Use Interface
Use Interface If you wish to use a particular WAN interface, select the checkbox
and select the interface.
Click Save/Apply to take effect the settings.
To delete the entry from the routing table list, click its corresponding Delete button.
Page 39 / 50
User Manual
Page 39
of 50
RIP
NOTE: RIP CANNOT BE CONFIGURED on the WAN interface that has NAT enabled (such as
PPPoE).
To activate RIP for the WAN Interface, select the desired RIP version and operation and
place a check in the 'Enabled' checkbox. To stop RIP on the WAN Interface, uncheck the
'Enabled' checkbox. Click the 'Apply/Save' button to star/stop RIP and save the
configuration.
Quality of Service
QoS gives you the capability to specify the level of quality to be provided for specific
applications. By default, QoS is not enabled.
Page 40 / 50
User Manual
Page 40
of 50
Queue Config
The screen allows you to configure a QoS queue entry and assign it to a specific network
interface. Each of the queues can be configured for a specific precedence. The queue
entry configured here will be used by the classifier to place ingress packets appropriately.
Note: Lower integer values for precedence imply higher priority for this queue relative to
others Click 'Apply/Save' to save and activate the queue.
Click Add to create a QoS Queue Configuration.
QoS Classification
You can add or remove QoS Classification rules.
The screen creates a traffic class rule to classify the upstream traffic, assign queue which
defines the precedence and the interface and optionally overwrite the IP header DSCP
byte. A rule consists of a class name and at least one condition below. All of the specified
conditions in this classification rule must be satisfied for the rule to take effect. Click
'Save/Apply' to save and activate the rule.
Click Add to create a Network Traffic Class Rule.
Port Mapping
Port mapping allows you to create groups composed of the various interfaces available in
your router.
Port mapping supports multiple ports to PVC and bridging groups. Each group will
perform as an independent network. To support this feature, you must create mapping
groups with appropriate LAN and WAN interfaces using the Add button. The Remove
button will remove the grouping and add the ungrouped interfaces to the Default group.
Only the default group has IP interface.

Rate

4.5 / 5 based on 2 votes.

Popular Aztech Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top