1. Home
    2. /
  2. Manuals
    3. /
  3. Allied-Telesis
    4. /
  4. AT-iMG624A
    5. /
  5. 135
Page 671 / 998 Scroll up to view Page 666 - 670
VoIP EP command reference
VoIP phone ports
6-107
iMG/RG Software Reference Manual (Voice Service)
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set prt0 onhook-time 250
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE DELETE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SHOW
6.3.3.1.40 VOIP EP SET RXGAIN
Syntax
VOIP EP ANALOGUE SET <name> RXGAIN <gain>
Description
This command sets the input gain (in the direction from iMG/VoIP network to phone/
user) of the port referred to by the named access port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set prt0 rxgain –3.0
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE DELETE
Option
Description
Default Value
name
An existing access port. To display the existing
access port names, use the VOIP EP ANALOGUE
LIST command.
N/A
msecs
The on-hook time in milliseconds. Valid values are in
the range 100 to 500msec.
N/A
Option
Description
Default Value
name
An existing access port. To display the existing access
port names, use the VOIP EP ANALOGUE LIST
command.
N/A
gain
The value of rx gain in dB. Valid values are from –
48dB to +28dB.
N/A
Page 672 / 998
VoIP phone ports
VoIP EP command reference
iMG/RG Software Reference Manual (Voice Service)
6-108
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SHOW
6.3.3.1.41 VOIP EP SET STUTTER-DIAL-TONE
Syntax
VOIP EP ANALOGUE SET <name> STUTTER-DIAL-TONE {PERIODIC|SIN-
GLE-REPETITION}
Description
This command sets the mode to play the stutter dial tone usually used to signal a waiting
message is available. The tone can be played periodically or only once (single repetition).
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set tel1 stutter-dial-tone periodic
6.3.3.1.42 VOIP EP SET SUPPLEMENTARY-SERVICE-PREFIX
Syntax
VOIP EP ANALOGUE SET <name> SUPPLEMENTARY-SERVICE-PREFIX
<digit-map>
Description
This command sets a prefix used by iMG to switch the status of the supplementary ser-
vices. When the user dials this prefix iMG plays the “stutter dial”, the user must dial a
phone number. iMG sends an INVITE containing the prefix and dialed number. The
server recognizes the prefix and used the dialed number to enable or disable some sup-
plementary services. The effects on this INVITE on the server depend on the server pro-
visioning. The feature is available only on SIP protocol and must be supported by the SIP
server.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Option
Description
Default Value
name
An existing access port. To display the existing access
port names, use the VOIP EP ANALOGUE LIST com-
mand.
N/A
Page 673 / 998
VoIP EP command reference
VoIP phone ports
6-109
iMG/RG Software Reference Manual (Voice Service)
Example
--> voip ep analogue set tel1 supplementary-service-prefix *222
6.3.3.1.43 VOIP EP SET TXGAIN
Syntax
VOIP EP ANALOGUE SET <name> TXGAIN <gain>
Description
This command sets the output gain (in the direction from phone/user to iMG/VoIP net-
work) of the port referred to by the named access port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set prt0 txgain –3.0
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE DELETE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SHOW
Option
Description
Default Value
name
Identifies the access port, 1 to 16 characters in length.
Valid characters are any printable characters, except
code 0x2E and 0x2F; digits cannot be used as first
character and if the space character is present, the
string must be quoted.
N/A
<digit-map>
is the expression string in use to know the end of
dialling phase. Valid value is either the string is “none”
or characters like digit and
symbols ‘#’, ‘*’, ‘.’, ‘|’, ‘[’,
‘]’, ‘-‘.
“none”
Option
Description
Default Value
name
An existing access port. To display the existing
access port names, use the VOIP EP ANALOGUE
LIST command.
N/A
gain
The value of rx gain in dB. Valid values are from –
48dB to +28dB.
N/A
Page 674 / 998
VoIP phone ports
VoIP EP command reference
iMG/RG Software Reference Manual (Voice Service)
6-110
6.3.3.1.44 VOIP EP SET UNREGISTERED-TONE
Syntax
VOIP EP ANALOGUE SET <name> UNREGISTERED-TONE {ENABLE|DISABLE}
Description
This command enables/disables a tone generated when the user is not registered. By
default, if the user is not registered and no FDB entries exist a reorder tone is generated.
If the unregistered-tone is disabled, no tones are generated.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set tel1 unregistered-tone disabled
6.3.3.1.45 VOIP EP SET VAD
Syntax
VOIP EP ANALOGUE SET <name> VAD <status>
Description
This command enables or disables the voice activity detection feature on the port
referred to by the named access port.
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue set prt0 vad off
See also
VOIP EP ANALOGUE CREATE
VOIP EP ANALOGUE DISABLE
VOIP EP ANALOGUE DELETE
VOIP EP ANALOGUE ENABLE
VOIP EP ANALOGUE LIST
VOIP EP ANALOGUE SHOW
Option
Description
Default Value
name
An existing access port. To display the existing access port
names, use the VOIP EP ANALOGUE LIST command.
N/A
Option
Description
Default Value
name
An existing access port. To display the existing access port
names, use the VOIP EP ANALOGUE LIST command.
N/A
status
The status of the VAD feature.
Valid values are:
•
on
VAD enabled
•
off
VAD disabled
N/A
Page 675 / 998
VoIP EP command reference
VoIP phone ports
6-111
iMG/RG Software Reference Manual (Voice Service)
6.3.3.1.46 VOIP EP SHOW
Syntax
VOIP EP ANALOGUE SHOW <name>
Description
This command displays the following information about a named access port:
•
Physical Port
•
Typology
•
Operational status
•
Comfort Noise Generation (CNG)
•
Codec Capabilities
•
Country
•
Critical-digit time
•
Inter-digit time
•
Dialing Mode
•
Digit map
•
Dial mask
•
Line Echo Cancellation
•
Jitter Delay
•
Voice Activity Detection (VAD)
•
Off-hook time
•
On-hook time
•
Rx gain
•
Tx gain
•
Attached users
Options
The following table gives the range of values for each option, which can be specified with
this command, and a default value (if applicable).
Example
--> voip ep analogue show prt0
--> voip ep analogue show tel1
Option
Description
Default Value
name
An existing access port. To display the existing access port
names, use the VOIP EP ANALOGUE LIST command.
N/A

Rate

4 / 5 based on 3 votes.

Popular Allied-Telesis Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top