Page 76 / 128 Scroll up to view Page 71 - 75
80
C
HAPTER
5: R
OUTER
C
ONFIGURATION
Upgrade
Upgrade Screen
The Upgrade facility allows you to install on the Router any new releases
of system software that 3Com may make available. To install new
software, you first need to download the software from the 3Com
support web site to a folder on your computer. Once you have done this,
select
Browse
to tell your web browser where this file is on your
computer, and then click
Apply
. The file will be copied to the Router, and
once this has completed, the Router will restart. Although the upgrade
process has been designed to preserve your configuration settings, it is
recommended that you make a backup of the configuration beforehand,
in case the upgrade process fails for any reason (for example, the
connection between the computer and the Router is lost while the new
software is being copied to the Router).
Page 77 / 128
Advanced
81
The upgrade procedure can take up to two minutes, and is complete
when the Alert LED has stopped flashing and is permanently off. Make
sure that you do not interrupt power to the Router during the upgrade
procedure; if you do, the software may be corrupted and the Router may
not start up properly afterwards. .
Advanced
Selecting
Advanced
from the main menu displays the following five tabs
in your Web browser window:
Static Route
,
RIP
,
Security
!
and
!
Syslog.
Static Route
The Router supports static route functionality. Select the
Static Route
tab
to display the screen
/
Static Route screen
The following information is displayed for each static route:
Index - the index of the static route
Network Address - the network address of the route. If network
address and subnet mask are both set to 0.0.0.0, this is the default
route.
Subnet Mask - the subnet mask of the route. If network address and
subnet mask are both set to 0.0.0.0, this is the default route.
Gateway - the gateway used to route data to the network specified by
the network address.
Page 78 / 128
82
C
HAPTER
5: R
OUTER
C
ONFIGURATION
RIP
The Router supports the Routing Information Protocol (RIP). RIP allows
you to set up routing information on one RIP enabled device, and have
that routing information replicated to all RIP enabled devices on the
network. LAN and WAN interfaces can be configured independently of
each other.
Select the RIP tab to display the screen
/
RIP screen
Check the
Enable RIP Mode
check box to configure RIP on the Router.
Page 79 / 128
Advanced
83
DDNS
Dynamic Domain Name Server (DDNS) enables you to map a static
domain name to a dynamic IP address. The Router supports two DDNS
providers, TZO.com and DYNDNS.org. Before you can set up DDNS, you
must obtain an account, password and static domain name from your
DDNS provider. DDNS is disabled by default.
To set up DDNS:
1
Select
Advanced
from the main menu, then select the
DDNS
tab. The
DDNS screen displays.
DDNS screen
Page 80 / 128
84
C
HAPTER
5: R
OUTER
C
ONFIGURATION
2
Select a
DDNS Service
provider from the drop-down list. This can be
either TZO.com or DynDNS.org.
TZO.com
If you select TZO.com:
1
In the
Domain Name
text box, enter the domain name.
2
In the
E-mail
text box, enter the account name.
3
In the
Key
text box, enter the account password.
4
Click
Save
to make this service active.
DynDNS.org
If you select DYNDNS.org:
1
In the
Host Name
text box, enter the host name.
2
In the
Username
text box, enter the account name.
3
In the
Password
text box, enter the account password.
4
Click
Save
!
to make this service active.
!

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top