1. Home
    2. /
  2. Manuals
    3. /
  3. 2Wire
    4. /
  4. 2701HG-D Qwest
    5. /
  5. 24
Page 116 / 132 Scroll up to view Page 111 - 115
Management and Diagnostic Console
111
Advanced - DNS Resolve Page
The Advanced - DNS Resolve page allows users to name network devices (such as printers or Web servers)
so that they may be easily accessed by other users on the network.
Figure 50. MDC Advanced DNS Name Table Page
To add entries to the Name table:
1.
In the DNS name field, enter a name for the device.
2.
In the IP Address field, enter the device’s IP address.
3.
Click
ADD
.
4.
The Name table displays the name you defined for each device, the device’s IP address, and the entry
type. To remove the device from the Name table, click the
Remove
button.
Note:
To access this page, your organization must have the Remote Management feature
enabled. If the feature is not enabled, an error message will display when you click the link to
access this page.
Page 117 / 132
Management and Diagnostic Console
112
Advanced - Traffic Shaping Page
The Advanced - Traffic Shaping page allows users to change the 2Wire gateway’s maximum upstream
connection rate.
Figure 51. MDC Advanced Traffic Shaping Page
To change the gateway’s upstream connection rate:
1.
Check the
Enable Traffic Shaping
checkbox.
2.
In the New Upstream Rate field, enter the upstream rate at which you want the gateway to connect.
3.
Click the
Submit
button.
Note:
To access this page, your organization must have the Remote Management feature
enabled. If the feature is not enabled, an error message will display when you click the link to
access this page.
Warning:
Modifying the gateway’s configuration settings may impede or interrupt the user’s
broadband service, or violate the service provider’s service level agreement.
Page 118 / 132
Management and Diagnostic Console
113
Advanced - Link Manager States Page
The Advanced – Link Manager States page is a tree representation of the 2Wire gateway interface stack,
and shows the internal state of the 2Wire gateway.
Figure 52. MDC Advanced Link Manager States Page
The Link Manager States page is used to gather dynamic information on internal networking modules, and
is based on the runtime configuration of the 2Wire gateway. The information cannot be used to configure
the 2Wire gateway.
Page 119 / 132
Management and Diagnostic Console
114
To view information about each node, click the node link. Information displays below the Link Manager
States tree, and includes the following:
Node Information
Description
Link status
Up.
The link is functioning properly.
Climbing.
The link is attempting to establish a connection.
Down.
The link is not yet configured.
Error.
An error has occurred.
State changes
The number of times the state of the link has changed (since last
reboot).
Page 120 / 132
Management and Diagnostic Console
115
The following table shows the possible nodes that can display on the Link Manager States page.
The nodes that display are dependent on the 2Wire gateway. For example, 2Wire gateways that are not
connected to the Internet via ADSL will not display ADSL information.
Node
Description
root0
Root for configuration tree.
global0
Branch for all global configuration modules.
device0
Maintains the status and configuration for devices on the 2Wire gateway.
rnat0
Maintains the application mappings and pinholes for nodes on the 2Wire gateway.
route0
Maintains all static routes on the 2Wire gateway.
fw0
Maintains all firewall rules on the 2Wire gateway.
cms0
Monitors CMS connectivity and activity with the 2Wire gateway.
home0
Branch for the home network modules.
vlan0
Home network virtual LAN configuration module.
ipnet1
Home network IP configuration module.
vlanmon0
Home network virtual LAN monitor for activity.
ipbridge0
Home network IP bridge/DMZ configuration module.
ipnet2
Home network public IP network configuration module.
vlan3
Home network voice virtual LAN module.
bband0
Branch for the primary broadband network.
vlan1
Primary broadband virtual LAN configuration module.
dhcp0
Primary broadband DHCP client module.
ipnet0
Primary broadband IP configuration module.
dnstest0
Primary broadband DNS access test module.
vlan2
Primary broadband PPP bridge virtual LAN.
dsl0
DSL device control module.
apvc0
Primary broadband ATM and auto PVC search module.
pppoe0
Primary broadband PPPoE configuration module.
pppoa0
Primary broadband PPPoA configuration module.
rtatm0
Primary broadband routed ATM configuration module.

Rate

4.3 / 5 based on 3 votes.

Popular 2Wire Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top