Zoom 5354 Router Manual PDF (Setup & Configuration Guide)

Page 111 / 143 Scroll up to view Page 106 - 110

111

Table 30. WMM Menu Option

Option

Description

WMM Support

Select On to include the WME Information Element in beacon

frame.

No-Acknowledgement

Select On to not transmit acknowledgments for data.

Power Save Support

Select On to allow the AP (Cable Modem/Router) queuing

packets for stations/clients in power-save mode. Queued

packets are transmitted when the station/client notifies AP that

it has left power-save mode.

EDCA AP Parameters

Enter the transmit parameters for traffic transmitted from the

AP to the STA (station) for the four Access Categories (AC):

Best Effort (AC_BE), Background (AC_BK), Video (AC_VI)

and Voice (AC_VO). Transmit parameters include Contention

Window (CWmin and CWmax), Arbitration Inter Frame

Spacing Number (AIFSN), and Transmit Opportunity Limit

(TXOP Limit).

There are also two AP-specific settings:



Admission Control: Specify if admission control is

enforced for the Access Categories.



Discard Oldest First. Specify the discard policy for the

queues.

On

discards the oldest first and

Off

discards the

newest first.

EDCA STA

Parameters

Specifies the transmit parameters for traffic transmitted from

the STA (station) to the AP for the four Access Categories

(AC): Best Effort (AC_BE), Background (AC_BK), Video

(AC_VI), and Voice (AC_VO). Transmit parameters include

Contention Window (CWmin and CWmax), Arbitration Inter

Frame Spacing Number (AIFSN) and Transmit Opportunity

Limit (TXOP Limit).

WMM TXOP

Parameters

Specifies the transmit parameters for WMM TXOP

Parameters for the four Access Categories (AC): Best Effort

(AC_BE), Background (AC_BK), Video (AC_VI), and Voice

(AC_VO). Transmit parameters include Short Relay Limit,

Short Fallback Limit, Long Retry Limit, Long Fallback Limit

and Max Rate in 500kbps.

Bridging

The Bridging page allows you to configure WDS (Wireless Distribution System) feature.

Only those bridges listed in the Remote Bridges table will be granted access. APs must

operate in the same channel to be bridged together.

Page 112 / 143

112

To access the

Bridging

page:

1

Click

Wireless

in the menu bar.

2

Then click the

Bridging

submenu.

Figure 36 shows an example of the menu and Table 29 describes the items you can

select.

Figure 36. Example of Bridging Page

Table 31. Bridging Menu Option

Option

Description

Wireless

Bridging

Select to enable or disable wireless bridging.

Remote Bridges

Table of remote bridge MAC addresses authorized to establish a

wireless bridge. Up to 4 remote bridges may be connected.

Typically, you will also have to enter your AP’s MAC address on the

remote bridge. The Cable Modem/Router’s wireless MAC address

can be found on the Wireless Interfaces page.

Page 113 / 143

113

Media

The Media page allows you to change some settings that can impact performance in

certain situations

To access the

Media

page:

3

Click

Wireless

in the menu bar.

4

Then click the

Media

submenu.

Figure 37. Example of Media Page shows an example of the menu and Table 32.

Media

Options

describes the items you can select.

Figure 37. Example of Media Page

Table 32. Media Options

Option

Description

Band Steering

Not applicable to this product

Airtime

If a 802.11g or 802.11b, client connects to the Cable Modem/Router

Page 114 / 143

114

Fairness

enabling Airtime Fairness will prevent the lower speed clients from

slowing down the router. If no slower clients connect than leave this

setting disabled.

Traffic

Scheduler

When wireless network is congested the traffic scheduler will

control access to the wireless queue when it reaches over capacity.

Exhausted

Buffer Order

Scheduling

(EBOS)

This setting is only enabled when the traffic scheduler is enabled.

EBOS will allow the first service link priority in sending traffic.

Page 115 / 143

115

14

VPN (Virtual Private Network) Menu Options

The VPN Menu lets you:



Configure a VPN tunnel



View VPN event logs

Basic Setting

This page allows you to enable VPN protocols and manage VPN tunnels. A virtual

private network (VPN) is a computer network in which some of the links between nodes

are carried by open connections or virtual circuits within some larger network (e.g., the

Internet) as opposed to by physical wires, as in a traditional private network. A VPN can

be used to separate the traffic of different user communities over an underlying network

with strong security features.

To access the

Basic

page:

1

Click

VPN

in the menu bar.

2

Then click the

Basic

submenu.

Figure 38 shows an example of the menu and Table 30 describes the items you can

select.

Rate

Popular Zoom Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share