1. Home
    2. /
  2. Manuals
    3. /
  3. Zhone
    4. /
  4. 6211-I3-xxx
    5. /
  5. 4
Page 16 / 107 Scroll up to view Page 11 - 15
Package Contents
In addition to this document, your package should arrive containing the following:
•
6219-X1 ADSL 2+ 4 port router
•
12V 1 A power adapter
•
RJ-11 telephone cable
•
RJ-45 Ethernet cable
•
User Manual / Quick Guide
Safety Instructions
Place your modem on a flat surface close to the cables in a location with sufficient ventilation.
To prevent overheating, do not obstruct the ventilation openings of the device.
Plug the device into a surge protector to reduce the risk of damage from power surges and
lightning strikes.
Operate this equipment only from an electrical outlet with the correct power source as indicated
on the adapter.
Do not open the cover of the device. Opening the cover will void any warranties on the
equipment.
Do not use another power adapter except for the one which accompanies the unit.
Unplug equipment first before cleaning. A damp cloth can be used to clean the equipment. Do not
use liquid / aerosol cleaners or magnetic / static cleaning devices.
6219-X1 Router Users Guide
16
Downloaded from
www.Manualslib.com
manuals search engine
Page 17 / 107
Front Panel
LED
Mode
INDICATION
Solid
green
Boot-up successful
Solid red
Router is booting up or there is problem with internal Power On Self
Test (POST )diagnostic
Power
No light
The router may not be turned on. Check if the power adapter is
connected to the modem and plugged in
Solid
DSL is not connected
Alarm
No light
DSL is linked successfully
Solid on
green
Ethernet interface is successfully connected to a device through the
LAN port
Flashing
The router is sending or receiving data over Ethernet
LAN 1-4
Off
No LAN Link
Solid
Wireless access point option is enabled
No light
Wireless access point
is disabled
WIFI
Blinking
Wireless traffic activity
Solid
Connection established. The router is able to communicate with your
ISP via ADSL
DSL
Flashing
The router is attempting to connect to your ISP
Solid
ADSL is connected
No light
ADSL is not connected. The ALARM LED will be red
Internet
Blinking
The router is connected to the LAN
6219-X1 Router Users Guide
17
Downloaded from
www.Manualslib.com
manuals search engine
Page 18 / 107
Back Panel
NOTE:
The below port descriptions are listed as they appear on the back panel from left to right.
Port
Description
Phone
RJ-11 cable connects to telephone (no external splitter necessary;
unit has internal splitter).
Line
RJ-11 cable connects between telephone and the LINE port using a
splitter (not included) if needed.
LAN1 – LAN4
RJ-45 connects the unit to an Ethernet device such as a PC or a
switch.
Reset / Default
Restart
—press the button for less than 4 seconds.
Default settings
—press the button for 4 seconds or longer.
Warning :
pressing the RESET button may erase the
configuration your service provider has loaded in the
modem and may cause service disruption.
Power
Connects to a 12V 1A power adapter.
6219-X1 Router Users Guide
18
Downloaded from
www.Manualslib.com
manuals search engine
Page 19 / 107
Chapter 2
Hardware Installation and PC Setup
Overview
This chapter provides basic instructions for connecting the router to a computer or a LAN and to
the Internet using DSL. The first part provides instructions to set up the hardware, and the second
part describes how to prepare your PC for use with the router. Refer to Chapter 3, Using the Web
Interface for configuration instructions.
It is assumed that you have already subscribed to DSL service with your telephone company or
other Internet service provider (ISP).
Connecting your hardware
Shut down your PC before connecting the router. To connect your modem:
1.
Connect the ADSL Line and Telephone
Connect one end of an RJ-11 cable from your ADSL connection and the other end to the
LINE port of the modem.
Use a second RJ-11 cable to connect between a telephone and the PHONE port of the
modem.
2.
Connect the PC to the Router
To use the Ethernet connection, connect the Ethernet cable from the computer directly to the
router. Connect one end of the Ethernet cable to one of the four ports labelled LAN on the
back of the router and attach the other end to the Ethernet port of your computer.
3.
Connect the Power Adapter
Complete the process by connecting the AC power adapter to the POWER connector on the
back of the device and plug the adapter into a wall outlet or power strip. Then turn on and
boot up your PC and any LAN devices, such as hubs or switches, and any computers
connected to them.
6219-X1 Router Users Guide
19
Downloaded from
www.Manualslib.com
manuals search engine
Page 20 / 107
Mounting the Router
The router can be mounted on the wall with two screws. Mounting can be done on wall material
including concrete, wood, or drywall. Select an appropriate location free from obstructions or any
possible interference. Make sure the cables can be easily attached to the router without strain.
The illustration below shows how to mount the router horizontally on a wall.
Standing the Router Vertically
The router can be set vertically on the desktop or other surface. On the right side of the unit as it
sits horizontally is a foot which can be rotated.
6219-X1 Router Users Guide
20
Downloaded from
www.Manualslib.com
manuals search engine

Rate

4.5 / 5 based on 2 votes.

Popular Zhone Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top