1. Home
    2. /
  2. Manuals
    3. /
  3. Westell
    4. /
  4. C90-327W30-06
    5. /
  5. 7
Page 31 / 126 Scroll up to view Page 26 - 30
030-300613 Rev A
31
August 2009
User Guide
VersaLink Wireless Gateway (Model 7500)
If you do not have a DSL sync, first check your physical connections. (Refer to section 5, “Hardware Installations,”
if needed.) If the problem persists, contact your ISP for further instructions.
Congratulations! You have established an Internet connection. You can now
Go!
browse the Internet. For example, to
visit Westell’s home page, type
in your Internet browser’s address bar, and then press
Enter
on your keyboard.
7.5
Disconnecting from an Internet Session
If you have finished browsing the Internet and want to disconnect from your ISP, click the
Add/Edit Connection
link from the
Broadband Connection
panel. The following
Home > Connection Overview
screen will appear.
Click
disconnect
and then
OK
.
IMPORTANT:
If you disconnect the PPP session, this will disconnect the Gateway from the Internet, and Internet
access for all users connected to the Gateway will be down until the PPP session is re-established.
If you clicked the
disconnect
button in the
Home > Connection Overview
screen, after a brief moment,
PPP
Status
should display DOWN. This means that you no longer have a PPP session. However, your DSL session will
not be affected. When you are ready to end your DSL session, simply turn off the Gateway via the
POWER
switch
on the Gateway’s rear panel.
When you are ready to establish a PPP session again, click the
connect
button in the
Home > Connection
Overview
screen. If you have previously turned off the Gateway, first turn on the Gateway, and then log on to your
account profile to establish a PPP session.
Page 32 / 126
030-300613 Rev A
32
August 2009
User Guide
VersaLink Wireless Gateway (Model 7500)
NOTE:
When you are ready to exit the Gateway’s interface, click on the
X
(close) in the upper-right corner of the
browser window. This will not affect your PPP Status; i.e., your PPP session will not be disconnected. You must
click the
disconnect
button to disconnect your PPP session. To restore this interface, open your Internet browser
window, type
in the browser’s address bar, and then press
Enter
on your keyboard. Type your
User name
and
Password
in the pop-up screen as needed.
7.6
Changing the Administration Password
It is recommended that you change the administration password of your Gateway after completing initial installation
and setup. You can accomplish this through the
Change Password
screen (
Security > Change Password
). This
screen allows you to change the default administration name and password to values of your choice.
IMPORTANT:
1. The
Security > Change Password
screen allows you to
use
admin
as your
administrator name
(your
administrator name can match your user name). However, you may not use
password
as your
administrator
password
. The values in these fields are case sensitive. Once you decide on an administrator name and password,
please record them for future reference.
2. This feature changes the Administrator’s password, not the PPP password.
Type your
Administration Name
and your
Administration
Password
in the fields provided, and then click
change
and
OK.
The password fields will be masked for security purposes.
Type a new password.
(Do not type the word
password
here.)
Type
admin
or
the name of
your choice.
If you clicked
OK
after clicking
change
, the following screen will appear.
Type in your new
User name
and
Password
in the fields provided, and then click
OK
.
Page 33 / 126
030-300613 Rev A
33
August 2009
User Guide
VersaLink Wireless Gateway (Model 7500)
8.
SETTING UP MACINTOSH OS X
This section provides instructions on how to use Macintosh Operating System 10 with the Gateway. Follow the
instructions in this section to create a new network configuration for Macintosh OS X.
NOTE:
Macintosh computers must use the Gateway’s Ethernet installation. Refer to section 5, “Hardware
Installations,” for details.
8.1
Opening the System Preference Screen
After you have connected the Gateway to the Ethernet port of your Macintosh, the screen below will appear. Click
the
Apple
icon in the upper-left corner of the screen, and select
System Preferences
.
8.2
Choosing the Network Preferences
After selecting
System Preferences
from the previous screen, the following screen will appear. Click the
Network
icon.
Page 34 / 126
030-300613 Rev A
34
August 2009
User Guide
VersaLink Wireless Gateway (Model 7500)
8.3
Creating a New Location
After clicking the
Network
icon, the following screen will appear. Select
New Location
from the
Location
field.
8.4
Naming the New Location
After selecting
New Location
in the
Network
screen, the following screen will appear. In the field labeled
Name your new location:
, change the text from
Untitled
to
Westell
. Click
OK
.
8.5
Selecting the Ethernet Configuration
After clicking
OK
in the
Name your new location:
screen, the
Network
screen will appear. The
Network
screen
displays the settings for the newly created location. From the
Configure
field in the
Network
screen, select
Built-in
Ethernet
. Click
Save
to save the settings.
NOTE:
Default settings for the Built-in Ethernet configuration are sufficient to operate the Gateway.
Page 35 / 126
030-300613 Rev A
35
August 2009
User Guide
VersaLink Wireless Gateway (Model 7500)
8.6
Checking the IP Connection
To verify that the computer is communicating with the Gateway, please follow these steps:
1.
Go to the
Apple
icon in the upper-left corner of the screen, and select
System Preferences
.
2.
In the
System Preferences
screen, click the
Network
icon. The
Network
screen will appear.
3.
In the
Configure
field in the
Network
screen, select
Built-in Ethernet
.
4.
View the
IP address
field. An IP address that begins with
192.168.1
should appear.
Congratulations! You have successfully verified communication between the computer and Gateway. Now, go to
section 8.7, “Accessing Your Gateway,” to access your Gateway’s Web pages.
NOTE:
The Gateway’s DHCP server provides this IP address. If this IP address is not displayed, check the
Gateway’s wiring connection to the PC. If necessary, refer to section 5, “Hardware Installations,” for instructions.
8.7
Accessing Your Gateway
In your Internet Explorer Web browser address bar, type
. Next, press
Enter
on your keyboard.

Rate

3.5 / 5 based on 2 votes.

Popular Westell Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top