Page 16 / 80 Scroll up to view Page 11 - 15
15
Accessing the Network
The Verizon Wireless MiFi 2200 supports Verizon Wireless
Mobile Broadband
and National
Access
service for a superior wireless data connection.
Mobile Broadband/National
Access
Now you can get the broadband-like speed you require to work efficiently outside the home
or office. You can connect to the Internet, corporate intranet, check your email and download
attachments with average download speeds of 600 kbps–1.4 Mbps. Mobile Broadband gives you
the freedom to stay productive and connected whether you’re on the road or in a meeting across
town. You also receive National
Access
service when outside the Mobile Broadband Rate and
Coverage Area. National
Access
is available in thousands of cities and towns and allows download
speeds of 60-80 kbps and burst up to 144 kbps.
Mobile Broadband with EVDO Rev. A
Download: typical download speeds of 600 kbps–1.4 Mbps.
Upload: typical upload speeds of 500-800 kbps.
Mobile Broadband with EVDO Rev. 0
Download: typical download speeds of 400-700 kbps.
Upload: typical upload speeds of 60-80 kbps.
Subject to Customer Agreement, Calling Plan, credit approval & other service terms.
Mobile Broadband Rev.A speed claim based on our network tests with 5 MB FTP data files without compression. Verizon
Wireless is rapidly adding Rev. A capability to your Mobile Broadband service area. Your Mobile Broadband Rev. A-enabled
device will indicate coverage when you are in a Mobile Broadband Rev. A service area. When outside the Rev. A service area,
your wireless device will revert to Mobile Broadband Rev. 0 (typical download speeds will be 400–700 Kbps and upload speeds
will be 60–80 Kbps) or National
Access
coverage areas, where available. Actual throughput speed and coverage may vary.
Speed claims not applicable when roaming.
National
Access
Rev.0 speed claim based on our network test with 101 KB FTP data files, without compression. Actual
throughout speed and coverage may vary. Speed claim not applicable when roaming.
WiFi 802.11b and 802.11g
802.11b uses the 2.4 GHz frequency with a bandwidth of 11 Mbps.
802.11g uses the 2.4 GHz frequency with a bandwidth of 54 Mbps.
Page 17 / 80
16
Using the Device for the First Time
IMPORTANT
Do not connect MiFi 2200 to a USB hub, as it might not provide sufficient power.
To get started, follow these steps.
±
Confirm your computer meets the minimum system requirements. [See
System
Requirements
(page 7).
]
Insert and charge the battery. [See
Insert and Charge the Battery
(page 17).
]
Connect the device to your computer with the USB cable. [See
Connect the Device to the
Computer with the USB Cable
(page 18).
]
Install the
VZ
Access Manager software. [See
Install and Set Up the Software
(page 14).
]
Activate MiFi 2200. [See
Activate Your Device
(page 24).
]
IMPORTANT
MiFi 2200 requires an activated account with Verizon Wireless to function.
Activation must be performed within a Mobile Broadband and/or National
Access
coverage area
while connected to a computer using the USB cable.
VZ
Access Manager must be installed prior
to activation.
MiFi 2200 includes software and drivers in its flash memory, so no installation CD is needed. The
device automatically installs the software the first time it is inserted into the computer’s USB port.
Page 18 / 80
17
Insert and Charge the Battery
IMPORTANT
Before you use your device, be sure to charge the battery for at least 2.5 hours to
ensure a full initial charge.
MiFi 2200 requires an activated account with a network operator.
To insert and charge the battery
±
Open the battery compartment, located on the bottom of the device.
Insert the battery by lining up the gold-colored contact points on the battery with the gold-
colored contact points in the battery compartment.
Once the battery is secure, place the battery cover back on the device until it locks into
place.
Connect the microUSB end of the AC wall charger to the microUSB port of the device as
shown.
Page 19 / 80
18
Plug the other end of the AC wall charger into the appropriate electrical outlet. Charge for at
least two and a half hours.
CAUTION!
Use only batteries and chargers with your device that have been approved by
Verizon Wireless or Novatel Wireless. The failure to use approved batteries and chargers may
increase the risk that your device will overheat, catch fire, or explode, resulting in serious bodily
injury, death, or property damage.
You are now ready to install the drivers and
VZ
Access Manager software. The first time you use the
device, you must connect MiFi 2200 to your computer with the microUSB cable (included).
Connect the Device to the Computer with the USB Cable
To connect the device to the computer
±
Grip MiFi 2200 by its sides and gently connect the small end of the microUSB cable to the
microUSB port on the device.
The cable should fit easily into the device. Do not force the cable into the device as this might
damage both the cable and the device.
Connect the large end of the microUSB cable to your computer’s USB port.
The cable should fit easily into the port. Do not force the cable into the port as this might
damage both the cable and the port.
NOTE 
If you have difficulty inserting the cable into your computer’s USB port, verify that you are inserting
the cable in the correct orientation and that you are using a Type A USB port.
The following occurs:
±
The status icon appears in the system tray / notification area (Windows) or in the menu bar
(Mac).
n
Page 20 / 80
19
MiFi 2200 is powered on automatically and begins charging.
IMPORTANT
The recommended minimum distance between you and the device is 8 inches.
Extend the microUSB cable so MiFi is at least 8 inches from your body.
Power MiFi 2200 On and Off
Power On
Press the Power Button until the Power Button LED is solid green.
Power Off
±
If the device is plugged into your computer with the USB Cable, unplug the USB cable from
the device first.
Press and hold the Power Button until the Power Button LED shuts off.

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top