Page 121 / 130 Scroll up to view Page 116 - 120
TL-WR842ND
300Mbps Multi-Function Wireless N Router
- 113 -
Figure A-4
Virtual Servers
Figure A-5
Add or Modify a Virtual server Entry
)
Note:
Your opposite side should call your WAN IP, which is displayed on the “Status” page.
4)
How to enable DMZ Host: Log in to the Router, click the “
Forwarding
” menu on the left
of your browser, and click "
DMZ
" submenu. On the "DMZ" page, click
Enable
radio
button and type your IP address into the “DMZ Host IP Address” field, using
192.168.0.169 as an example, remember to click the
Save
button.
Figure A-6
DMZ
5)
How to enable H323 ALG: Log in to the Router, click the “
Security
” menu on the left of
your browser, and click “
Basic Security
” submenu. On the “
Basic Security
” page,
Page 122 / 130
TL-WR842ND
300Mbps Multi-Function Wireless N Router
- 114 -
check the
Enable
radio button next to
H323 ALG
. Remember to click the
Save
button.
Figure A-7
Basic Security
4.
I want to build a WEB Server on the LAN, what should I do?
1)
Because the WEB Server port 80 will interfere with the WEB management port 80 on the
Router, you must change the WEB management port number to avoid interference.
2)
To change the WEB management port number: Log in to the Router, click the “
Security
menu on the left of your browser, and click "
Remote Management
" submenu. On the
"
Remote Management
" page, type a port number except 80, such as 88, into the "Web
Management Port" field. Click
Save
and reboot the Router.
Page 123 / 130
TL-WR842ND
300Mbps Multi-Function Wireless N Router
- 115 -
F
igure A-8
Remote Management
)
Note:
If the above configuration takes effect, you can visit and configure the Router by typing
(the Router’s LAN IP address: Web Management Port) in the address
field of the Web browser. If the LAN IP of the modem connected with your router is
192.168.0.x, the default LAN IP of the Router will automatically switch from 192.168.0.1 to
192.168.1.1 to avoid IP conflict; in this case, please try
.
3)
Log in to the Router, click the “
Forwarding
” menu on the left of your browser, and click
the "
Virtual Servers
" submenu. On the "
Virtual Servers
" page, click
Add New…
, then
on the “
Add or Modify a Virtual Server
” page, enter “80” into the blank next to the
Service Port
”, and your IP address next to the “
IP Address
”, assuming 192.168.0.188
for an example, remember to
Enable
and
Save
.
Figure A-9 Virtual Servers
Page 124 / 130
TL-WR842ND
300Mbps Multi-Function Wireless N Router
- 116 -
Figure A-10 Add or Modify a Virtual server Entry
5.
The wireless stations cannot connect to the Router.
1)
Make sure the "
Wireless Router Radio
" is enabled.
2)
Make sure that the wireless stations' SSID accord with the Router's SSID.
3)
Make sure the wireless stations have right KEY for encryption when the Router is
encrypted.
4)
If the wireless connection is ready, but you can’t access the Router, check the IP Address
of your wireless stations.
Page 125 / 130
TL-WR842ND
300Mbps Multi-Function Wireless N Router
- 117 -
Appendix B: Configuring the PCs
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP.
First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed.
1.
Install TCP/IP component
1)
On the Windows taskbar, click the
Start
button, point to
Settings
, and then click
Control
Panel
.
2)
Click the
Network and Internet Connections
icon, and then click on the
Network
Connections
tab in the appearing window.
3)
Right click the icon that showed below, select Properties on the prompt page.
Figure B-1

Rate

4 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top