Page 16 / 112 Scroll up to view Page 11 - 15
TL-WR841N/TL-WR841ND
300Mbps Wireless N Router User Guide
- 7 -
Chapter 2. Connecting the Router
2.1 System Requirements
¾
Broadband Internet Access Service (DSL/Cable/Ethernet)
¾
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
¾
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
¾
TCP/IP protocol on each PC
¾
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
2.2 Installation Environment Requirements
¾
Place the Router in a well ventilated place far from any heater or heating vent
¾
Avoid direct irradiation of any strong light (such as sunlight)
¾
Keep at least 2 inches (5 cm) of clear space around the Router
¾
Operating Temperature: 0
~40
(32
~104
)
¾
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1.
Power off your PC, Cable/DSL Modem, and the Router.
2.
Locate an optimum location for the Router. The best place is usually at the center of your
wireless network.
3.
Adjust the direction of the antenna. Normally, upright is a good direction.
4.
Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
in Figure 2-1. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
5.
Connect the DSL/Cable Modem to the WAN port on the Router, shown in Figure 2-1.
Page 17 / 112
TL-WR841N/TL-WR841ND
300Mbps Wireless N Router User Guide
- 8 -
6.
Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
7.
Power on your PC and Cable/DSL Modem.
Figure 2-1
Hardware Installation of the TL-WR841ND 300Mbps Wireless N Router
Page 18 / 112
TL-WR841N/TL-WR841ND
300Mbps Wireless N Router User Guide
- 9 -
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your TL-WR841ND 300Mbps
Wireless N Router using
Quick Setup
Wizard
within minutes.
3.1 TCP/IP Configuration
The
default
domain
name
of
the
TL-WR841ND
300Mbps
Wireless
N
Router
is
http://tplinklogin.net
, the default IP address is 192.168.0.1, and the default Subnet Mask is
255.255.255.0. These values can be changed as you desire. In this guide, we use all the default
values for description.
Connect the local PC to the LAN ports of the Router. And then you can configure the IP address
for your PC in the following two ways.
¾
Configure the IP address manually
1)
Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to
Appendix B: "Configuring the PC"
.
2)
Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is any number
from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.0.1 (The
Router's default IP address)
¾
Obtain an IP address automatically
1)
Set up the TCP/IP Protocol in "
Obtain an IP address automatically
" mode on your PC.
If you need instructions as to how to do this, please refer to
Appendix B: "Configuring the
PC”.
2)
Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the
command prompt
to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type
, and then press
Enter
.
¾
If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.
Page 19 / 112
TL-WR841N/TL-WR841ND
300Mbps Wireless N Router User Guide
- 10 -
Figure 3-1
Success result of Ping command
¾
If the result displayed is similar to the Figure 3-2, it means the connection between your PC
and the Router is failed.
Figure 3-2
Failure result of Ping command
Please check the connection following these steps:
1.
Is the connection between your PC and the Router correct?
)
Note:
The 1/2/3/4 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter
should be lit.
2.
Is the TCP/IP configuration for your PC correct?
)
Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
Page 20 / 112
TL-WR841N/TL-WR841ND
300Mbps Wireless N Router User Guide
- 11 -
3.
Is the default LAN IP of the Router correct?
)
Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type
ping 192.168.1.1
, and then press
Enter
.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the TL-WR841ND 300Mbps Wireless
N Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web
browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1.
To access the configuration utility, open a web-browser and type in the default domain name
http://tplinklogin.net
in the address field of the browser.
Figure 3-3
Log in the Router
After a moment, a login window will appear, similar to the Figure 3-4. Enter
admin
for the
User Name and Password, both in lower case letters. Then click the
OK
button or press the
Enter
key.
Figure 3-4
Login Windows
)
Note:
If the above screen does not pop-up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top