Page 21 / 104 Scroll up to view Page 16 - 20
TL-WR840N
300Mbps Wireless N Router User Guide
- 12 -
Figure 3-7 Quick Setup – L2TP/Russia L2TP
User Name
/
Password -
Enter the
User Name
and
Password
provided by your ISP.
These fields are case-sensitive. If you have difficulty with this process, please contact
your ISP.
Select
Static IP
if IP Address/ Subnet Mask/ Gateway and DNS server address have been
provided by your ISP. Then please enter server IP address or domain name provided by your
ISP, and also enter the corresponding parameters.
Select
Dynamic IP
if none of the above parameters are provided. Then you just need to enter
server IP address or domain name provided by your ISP.
2) If the connection type detected is
PPTP
, the next screen will appear as shown in Figure
3-8.Configure the following parameters and then click
Next
to continue.
Page 22 / 104
TL-WR840N
300Mbps Wireless N Router User Guide
- 13 -
Figure 3-8 Quick Setup – PPTP/Russia PPTP
User Name
/
Password -
Enter the
User Name
and
Password
provided by your ISP.
These fields are case-sensitive. If you have difficulty with this process, please contact
your ISP.
Select
Static IP
if IP Address/ Subnet Mask/ Gateway and DNS server address have been
provided by your ISP. Then please enter server IP address or domain name provided by your
ISP, and also enter the corresponding parameters.
Select
Dynamic IP
if none of the above parameters are provided. Then you just need to enter
server IP address or domain name provided by your ISP.
3)
If the connection type detected is
PPPoE
, the next screen will appear as shown in Figure
3-9.
Figure 3-9 Quick Setup - PPPoE
Page 23 / 104
TL-WR840N
300Mbps Wireless N Router User Guide
- 14 -
User Name
/
Password -
Enter the
User Name
and
Password
provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please contact your
ISP.
Confirm Password -
Re-enter the password provided by your ISP to ensure the
Password you entered is correct. If the Password is different from the Confirm Password,
the screen will appear as shown below. Click
OK
, and re-enter the Password
and
Confirm Password.
4) If the connection type detected is
Dynamic IP
, the next screen will appear as shown in
Figure 3-10.
If you are visiting the Router from the main computer, please select
Yes
, and then
click
Clone MAC Address
.
Figure 3-10
Quick Setup – MAC Clone
If you are visiting the Router from another computer, rather than the main computer,
please select
No
, and then enter the main computer’s MAC in the field
WAN MAC
Address
.
Figure 3-11
Quick Setup – MAC Clone
Page 24 / 104
TL-WR840N
300Mbps Wireless N Router User Guide
- 15 -
5) If the connection type detected is
Static IP
, the next screen will appear as shown in
Figure 3-12.
Figure 3-12
Quick Setup - Static IP
IP Address -
This is the WAN IP address as seen by external users on the Internet
(including your ISP). Enter the IP address into the field.
Subnet Mask -
The Subnet Mask is used for the WAN IP address, it is usually
255.255.255.0.
Default Gateway -
Enter the gateway IP address into the box if required.
Primary
DNS -
Enter the DNS Server IP address into the box if required.
Secondary DNS -
If your ISP provides another DNS server, enter it into this field.
4.
Click
Next
to continue, the Wireless settings page will appear as shown in Figure 3-13.
Figure 3-13
Quick Setup – Wireless
Page 25 / 104
TL-WR840N
300Mbps Wireless N Router User Guide
- 16 -
Wireless Radio -
The wireless radio can only be enabled/disabled by using the WIFI
ON/OFF switch on the device.
Wireless Network Name -
Enter a value of up to 32 characters. The same name of
SSID (Service Set Identification) must be assigned to all wireless devices in your
network. Considering your wireless network security, the default SSID is set to be
TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s
MAC address). This value is case-sensitive. For example,
TEST
is NOT the same as
test
.
Region
-
Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
Limited by local law regulations, version for North America does not have region
selection option.
Mode -
This field determines the wireless mode which the Router works on.
Channel Width -
Select any channel width from the drop-down list. The default setting
is automatic, which can adjust the channel width for your clients automatically.
Channel -
This field determines which operating frequency will be used. The default
channel is set to
Auto
, so the AP will choose the best channel automatically. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point.
Disable Security -
The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without encryption. It is
recommended strongly that you choose one of following options to enable security.
WPA-PSK/WPA2-PSK -
Select WPA based on pre-shared passphrase.
PSK Password
- You can enter
ASCII
or
Hexadecimal
characters.
For
ASCII
, the key can be made up of any numbers 0 to 9 and any letters A to Z, the
length should be between 8 and 63 characters.
For
Hexadecimal
, the key can be made up of any numbers 0 to 9 and letters A to F,
the length should be between 8 and 64 characters.
Please also note the key is case sensitive, this means that upper and lower case
keys will affect the outcome. It would also be a good idea to write down the key and
all related wireless security settings.
No Change -
If you chose this option, wireless security configuration will not change!

Rate

4 / 5 based on 3 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top