1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WR743ND
    5. /
  5. 20
Page 96 / 145 Scroll up to view Page 91 - 95
TL-WR743ND
150Mbps Wireless AP/Client Router
- 87 -
L2TP Passthrough
-
Layer 2 Tunneling Protocol (L2TP) is the method used to enable
Point-to-Point sessions via the Internet on the Layer 2 level. To allow L2TP tunnels to
pass through the Router, keep the default,
Enabled
.
IPSec Passthrough
-
Internet Protocol Security (IPSec) is a suite of protocols for
ensuring private, secure communications over Internet Protocol (IP) networks, through
the use of cryptographic security services. To allow IPSec tunnels to pass through the
Router, keep the default,
Enabled
.
ALG -
It is recommended to enable Application Layer Gateway (ALG) because ALG allows
customized Network Address Translation (NAT) traversal filters to be plugged into the
gateway to support address and port translation for certain application layer "control/data"
protocols such as FTP, TFTP, H323 etc.
FTP ALG -
To allow FTP clients and servers to transfer data across NAT, keep the
default
Enable
.
TFTP ALG -
To allow TFTP clients and servers to transfer data across NAT, keep the
default
Enable
.
H323 ALG -
To allow Microsoft NetMeeting clients to communicate across NAT, keep
the default
Enable
.
RTSP ALG -
To allow some media player clients to communicate with some streaming
media servers across NAT, click
Enable
.
Click the
Save
button to save your settings.
4.10.2 Advanced Security
Choose menu “
Security
→
Advanced Security
”, and then you can protect the Router from
being attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the screen as shown in Figure
4-46.
Page 97 / 145
TL-WR743ND
150Mbps Wireless AP/Client Router
- 88 -
Figure 4-46
Advanced Security
Packets Statistics Interval (5~60) -
The default value is 10. Select a value between 5 and
60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time
section of the packets statistics. The result of the statistics is used for analysis by SYN Flood,
UDP Flood and ICMP-Flood.
DoS protection -
Denial of Service protection. Check the Enable or Disable button to
enable or disable the DoS protection function. Only when it is enabled, will the flood filters be
enabled.
Note:
Dos Protection will take effect only when the
Traffic Statistics
in “
System Tool
→
Traffic
Statistics
” is enabled.
Enable ICMP-FLOOD Attack Filtering
-
Enable or Disable the ICMP-FLOOD Attack
Filtering.
ICMP-FLOOD Packets Threshold (5~3600)
-
The default value is 50. Enter a value
between 5
~
3600. When the current ICMP-FLOOD Packets number is beyond the set value,
the Router will startup the blocking function immediately.
Enable UDP-FLOOD Filtering
-
Enable or Disable the UDP-FLOOD Filtering.
Page 98 / 145
TL-WR743ND
150Mbps Wireless AP/Client Router
- 89 -
UDP-FLOOD Packets Threshold (5~3600)
-
The default value is 500. Enter a value
between 5
~
3600. When the current UPD-FLOOD Packets number is beyond the set value,
the Router will startup the blocking function immediately.
Enable TCP-SYN-FLOOD Attack Filtering
-
Enable or Disable the TCP-SYN-FLOOD
Attack Filtering.
TCP-SYN-FLOOD Packets Threshold (5~3600)
-
The default value is 50. Enter a value
between 5
~
3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set
value, the Router will startup the blocking function immediately.
Ignore Ping Packet From WAN Port
-
Enable or Disable Ignore Ping Packet From WAN
Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot
access the Router.
Forbid Ping Packet From LAN Port
-
Enable or Disable Forbid Ping Packet From LAN Port.
The default setting is disabled. If enabled, the ping packet from LAN cannot access the
Router. This function can be used to defend against some viruses.
Click the
Save
button to save the settings.
Click the
Blocked DoS Host List
button to display the DoS host table by blocking.
4.10.3 Local Management
Choose menu “
Security
→
Local Management
”, and then you can configure the management
rule in the screen as shown in Figure 4-47. The management feature allows you to deny
computers in LAN from accessing the Router.
Figure 4-47 Local Management
By default, the radio button “
All the PCs on the LAN are allowed to access the Router's
Web-Based Utility
” is checked. If you want to allow PCs with specific MAC Addresses to access
Page 99 / 145
TL-WR743ND
150Mbps Wireless AP/Client Router
- 90 -
the Setup page of the Router's Web-Based Utility locally from inside the network, check the radio
button “
Only the PCs listed can browse the built-in web pages to perform Administrator
tasks
”, and then enter each MAC Address in a separate field. The format for the MAC Address is
XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with MAC address listed can
use the password to browse the built-in web pages to perform Administrator tasks while all the
others will be blocked.
After click the
Add
button, your PC's MAC Address will be placed in the list above.
Click the
Save
button to save your settings.
Note:
If your PC is blocked but you want to access the Router again, use a pin to press and hold the
Reset Button
(hole) on the back panel for about 5 seconds to reset the Router’s factory defaults
on the Router’s Web-Based Utility.
4.10.4 Remote Management
Choose menu “
Security
→
Remote Management
”; you can configure the Remote Management
function in the screen as shown in Figure 4-48. This feature allows you to manage your Router
from a remote location via the Internet.
Figure 4-48
Remote Management
Web Management Port -
Web browser access normally uses the standard HTTP service
port 80. This Router's default remote management web port number is 80. For greater
security, you can change the remote management web port to a custom port by entering that
number in the box provided. Choose a number between 1 and 65534 but do not use the
number of any common service port.
Remote Management IP Address
-
This is the current address you will use when accessing
your Router from the Internet. This function is disabled when the IP address is set to the
default value of 0.0.0.0. To enable this function change 0.0.0.0 to a valid IP address. If set to
255.255.255.255, then all the hosts can access the Router from internet.
Note:
1. To access the Router, you should type your Router's WAN IP address into your browser's
address (in IE) or Location (in Navigator) box, followed by a colon and the custom port number.
For example, if your Router's WAN address is 202.96.12.8, and the port number used is 8080,
Page 100 / 145
TL-WR743ND
150Mbps Wireless AP/Client Router
- 91 -
please enter
in your browser. Later, you may be asked for the Router's
password. After successfully entering the username and password, you will be able to access
the Router's web-based utility.
2.
Be sure to change the Router's default password to a very secure password
.
4.11 Parental Control
Choose menu “
Parental Control
”; you can configure the parental control in the screen as shown
in Figure 4-49. The Parental Control function can be used to control the internet activities of the
child, limit the child to access certain websites and restrict the time of surfing.
Figure 4-49
Parental Control Settings
Parental Control -
Check
Enable
if you want this function to take effect, otherwise check
Disable
.
MAC Address of Parental PC -
In this field, enter the MAC address of the controlling PC, or
you can make use of the
Copy To Above
button below.
MAC Address of Your PC -
This field displays the MAC address of the PC that is managing
this Router. If the MAC Address of your adapter is registered, you can click the Copy To
Above button to fill this address to the MAC Address of Parental PC field above.
Website Description -
Description of the allowed website for the PC controlled.
Schedule
-
The time period allowed for the PC controlled to access the Internet. For detailed
information, please go to “
Access Control
→
Schedule
”.
Modify
-
Here you can edit or delete an existing entry.
To add a new entry, please follow the steps below.
1.
Click the
Add New…
button and the next screen will pop-up as shown in Figure 4-50.

Rate

4.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top