Page 76 / 84
Scroll up to view Page 71 - 75
TL-WR641G
108M Wireless Router User Guide
- 68 -
Figure A-5
)
Note:
Your opposite side should call your WAN IP, which is displayed on the “Status” page.
4)
How to enable DMZ Host: Login to the router, click the “Forwarding” menu on the left of
your browser, and click "DMZ" submenu. On the "DMZ" page, click “Enable” radio and
type your IP address into the “DMZ Host IP Address” field, using
192.168.1.169 as an
example, remember to click the "Save” button.
Figure A-6
4.
I want to build a WEB Server on the LAN, what should I do?
1)
Because the WEB Server port 80 will interfere with the WEB management port 80 on
the router, you must change the WEB management port number to avoid interference.
2)
To change the WEB management port number: Login to the router, click the “Security”
menu on the left of your browser, and click "Remote Management" submenu. On the
"Remote Management" page, type a port number except 80, such as 88, into the "Web
Management Port" field. Click “Save” and reboot the router.
Figure A-7
Page 77 / 84
TL-WR641G
108M Wireless Router User Guide
- 69 -
)
Note:
If the above configuration takes effect, to configure to the router by typing
(the router’s LAN IP address: Web Management Port) in the address field of the Web browser.
3)
Login to the router, click the “Forwarding” menu on the left of your browser, and click
the "Virtual Servers" submenu. On the "Virtual Server" page, click
Add New,
then on
the “Add or Modify a Virtual Server” page, enter “80” into the blank behind the “Service
Port”, and your IP address behind the IP Address, assuming
192.168.1.188 for an
example, remember to “Enable” and “Save”.
Figure A-8
Figure A-9
5.
The wireless stations cannot connect to the router.
1)
Make sure the "Wireless Router Radio" is enabled.
2)
Make sure that the wireless stations' SSID accord with the router's SSID.
3)
Make sure the wireless stations have right KEY for encryption when the router is
encrypted.
4)
If the wireless connection is ready, but you can’t access the router, check the IP
Address of your wireless stations.
Page 78 / 84
TL-WR641G
108M Wireless Router User Guide
- 70 -
Appendix B: Configuring the PC
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP.
First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed.
1.
Install TCP/IP component
1)
On the Windows taskbar, click the
Start
button, point to
Settings
, and then click
Control Panel
.
2)
Click the
Network and Internet Connections
icon, and then click on the
Network
Connections
tab in the appearing window.
3)
Right click the icon that showed below, select Properties on the prompt page.
Figure 1
4)
In the prompt page that showed below, double click on the
Internet Protocol
(TCP/IP)
.
Page 79 / 84
TL-WR641G
108M Wireless Router User Guide
- 71 -
Figure 2
5)
The following
TCP/IP Properties
window will display and the
IP Address
tab is open on
this window by default.
Now you have two ways to configure the
TCP/IP
protocol below:
¾
Setting IP address automatically
Select
Obtain an IP address automatically
, Choose
Obtain DNS server automatically
, as
shown in the Figure below:
Page 80 / 84
TL-WR641G
108M Wireless Router User Guide
- 72 -
Figure 3
¾
Setting IP address manually
1
Select
Use the following IP address
radio button. And the following items available
2
If the router's LAN IP address is
192.168.1.1, type IP address is 192.168.1.x (x is from 2 to
254), and
Subnet mask
is 255.255.255.0.
3
Type the router’s LAN IP address (the default IP is
192.168.1.1) into the
Default gateway
field.
4
Select
Use the following DNS server addresses
radio button. In the
Preferred
DNS
Server
field you can type the DNS server IP address, which has been provided by your ISP
19216811.live