Page 26 / 146 Scroll up to view Page 21 - 25
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 16 -
Wireless Network Name -
Also called the
SSID (Service Set Identification). Enter a
value of up to 32 characters. The same name must be assigned to all wireless devices
in your network. The default SSID is set to be TP-LINK_2.4GHz_XXXXXX. This value is
case-sensitive. For example,
TEST
is NOT the same as
test
.
Region
-
Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
Limited by local law regulations, version for North America does not have region
selection option.
Band -
This field displayed the operating frequency being configured.
Mode -
This field determines the wireless mode which the Router works on.
11b only -
Select if all of your wireless clients are 802.11b.
11g only -
Select if all of your wireless clients are 802.11g.
11n only-
Select only if all of your wireless clients are 802.11n.
11bg mixed -
Select if you are using both 802.11b and 802.11g wireless clients.
11bgn mixed -
Select if you are using a mix of 802.11b, 11g, and 11n wireless
clients.
Channel Width -
Select any channel width from the drop-down list. The default setting
is “Auto”, which can adjust the channel width for your clients automatically.
Channel -
This field determines which operating frequency will be used. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point. If you select “Auto”, then the AP will select the best
channel automatically.
Wireless Security
Disable Security -
The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without
encryption.
Enable Security (WPA-PSK/WPA2-PSK) –
It’s selected by default, with the
default PSK password the same as the default PIN code.
No Change -
If you chose this option, wireless security configuration will not
change!
Page 27 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 17 -
These settings are only for basic wireless parameters. For advanced settings, please refer to
4.6 Wireless 2.4GHz.
7.
Configure the basic parameters for 5GHz wireless network in the following screen as shown
in Figure 3-13, and then click
Next
.
Figure 3-13 Quick Setup – Wireless
Wireless Radio -
Choose from the drop-down list to enable or disable the wireless
radio.
Wireless Network Name -
Also called the
SSID (Service Set Identification). Enter a
value of up to 32 characters. The same name must be assigned to all wireless devices
in your network. The default SSID is set to be TP-LINK_5GHz_XXXXXX. This value is
case-sensitive. For example,
TEST
is NOT the same as
test
.
Region
-
Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
Limited by local law regulations, version for North America does not have region
selection option.
Band -
This field displayed the operating frequency being configured.
Mode -
This field determines the wireless mode which the Router works on.
11a only -
Select if all of your wireless clients are 802.11a.
Page 28 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 18 -
11n only-
Select only if all of your wireless clients are 802.11n.
11an mixed -
Select if you are using both 802.11a and 802.11n wireless clients.
Channel Width -
Select any channel width from the drop-down list. The default setting
is “Auto”, which can adjust the channel width for your clients automatically.
Channel -
This field determines which operating frequency will be used. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point. If you select “Auto”, then the AP will select the best
channel automatically.
Wireless Security
Disable Security -
The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without
encryption.
Enable Security (WPA-PSK/WPA2-PSK) –
It’s selected by default, with the
default PSK password the same as the default PIN code.
No Change -
If you chose this option, wireless security configuration will not
change!
These settings are only for basic wireless parameters. For advanced settings, please refer to
4.7 Wireless 5GHz.
8.
Then you will see the
Finish
page.
If you don’t make any change on the
Wireless
page, you will see the
Finish
page as
shown in Figure 3-14. Click the
Finish
button to finish the
Quick Setup
.
Figure 3-14 Quick Setup - Finish
If there is anything changed on the
Wireless
page, you will see the
Finish
page as
shown in Figure 3-15. Click the
Reboot
button to make your wireless configuration take
effect and finish the
Quick Setup
.
Page 29 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 19 -
Figure 3-15 Quick Setup – Finish
Page 30 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 20 -
Chapter 4. Configuring the Router
This chapter will show each Web page's key functions and the configuration way.
4.1
Login
After your successful login, you will see the sixteen main menus on the left of the Web-based utility.
On the right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
4.2
Status
The Status page provides the current status information about the Router. All information is
read-only.

Rate

3.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top