1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WDR4300
    5. /
  5. 25
Page 121 / 146 Scroll up to view Page 116 - 120
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 111 -
Note:
If you get Address not found error when you access a Web site, it is likely that your DNS servers
are set up improperly. You should contact your ISP to get DNS server addresses.
Get IPv6 with Unicast DHCP
- A few ISPs' DHCP servers do not support the broadcast
applications. If you can't get the IPv6 Address normally, you can choose Unicast. (You
generally need not to check this option).
IPv6 Address Assign Type
- There are two types of assignation for IPv6 address: SLAAC
(Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol
for IPv6) Server.
SLAAC
•
IPv6 Address Prefix
-The Prefix of IPv6 Address
DHCPv6 Server
•
Release Time
-
the length of time a network user will be allowed to keep connecting to the
router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the
DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value
is 86400 seconds.
•
IPv6 Address
- Displays the LAN IPv6 Address.
2)
Static IPv6
Figure 4-115 Static IPv6
Page 122 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 112 -
IPv6 Address
- Enter the IPv6 address in dotted-decimal notation provided by your ISP.
Default Gateway
- Enter the default gateway in dotted-decimal notation provided by your ISP.
MTU Size
- The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required,
and should not be done unless you are sure it is necessary for your ISP connection.
Primary DNS
- Enter the DNS IPv6 address in dotted-decimal notation provided by your ISP.
Secondary DNS
- Enter another DNS IPv6 address in dotted-decimal notation provided by
your ISP.
IPv6 Address Assign Type
- There are two types of assignation for IPv6 address: SLAAC
(Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol for
IPv6) Server.
SLAAC
•
IPv6 Address Prefix
-The Prefix of IPv6 Address
DHCPv6 Server
•
Release Time
-
the length of time a network user will be allowed to keep connecting to
the router with the current DHCPv6 Address. Enter the amount of time (in seconds) that
the DHCPv6 address will be leased. The time range is 1~691200 seconds. The default
value is 86400 seconds.
•
IPv6 Address
- Displays the LAN IPv6 Address.
3)
PPPoEv6
Figure 4-116 PPPoEv6
Page 123 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 113 -
User Name/Password
- Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Get IPv6 Address Way
•
Get non-temporary IPv6 address
- Get a non-temporary IPv6 address by DHCPv6
from the ISP.
•
Get IPv6 prefix delegation
- Get a prefix delegation IPv6 address by DHCPv6 from the
ISP, and the clients in LAN create IPv6 address with the delegation.
•
Use IP address specified by ISP
- Input a static IPv6 address from the ISP
Click the
Connect
button to connect immediately.
Click the
Disconnect
button to disconnect immediately.
IPv6 Address Assign Type
- There are two types of assignation for IPv6 address: SLAAC
(Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol
for IPv6) Server.
SLAAC
•
IPv6 Address Prefix
-The Prefix of IPv6 Address
DHCPv6 Server
•
Release Time
-
the length of time a network user will be allowed to keep connecting to the
router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the
DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value
is 86400 seconds.
•
IPv6 Address
- Displays the LAN IPv6 Address.
4)
Tunnel 6to4
Figure 4-117 Tunnel 6to4
Page 124 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 114 -
Address/Subnet Mask/Default Gateway
- the IPv4 address/ subnet mask/ default gateway
assigned, in dotted-decimal notation.
MTU Size
- The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1480 Bytes. For some ISPs, you may need to modify the MTU. But this is rarely required,
and should not be done unless you are sure it is necessary for your ISP connection.
If your ISP gives you one or two DNS IPv6 addresses, select
Use the following IPv6 DNS
Servers
and enter the
Primary IPv6 DNS
and
Secondary IPv6 DNS
into the correct fields.
Otherwise, the DNS servers will be assigned from ISP dynamically.
Primary IPv6 DNS
- Enter the DNS IPv6 address in dotted-decimal notation provided by your
ISP.
Secondary IPv6 DNS
- Enter another DNS IPv6 address in dotted-decimal notation provided
by your ISP.
IPv6 Address Assign Type
- There are two types of assignation for IPv6 address: SLAAC
(Stateless address auto-configuration) and DHCPv6 (Dynamic Host Configuration Protocol
for IPv6) Server.
SLAAC
•
IPv6 Address Prefix
-The Prefix of IPv6 Address
DHCPv6 Server
•
Release Time
-
the length of time a network user will be allowed to keep connecting to the
router with the current DHCPv6 Address. Enter the amount of time (in seconds) that the
DHCPv6 address will be leased. The time range is 1~691200 seconds. The default value
is 86400 seconds.
•
IPv6 Address
- Displays the LAN IPv6 Address.
4.21 System Tools
Figure 4-118 The System Tools menu
Page 125 / 146
TL-WDR4300
N750 Wireless Dual Band Gigabit Router
- 115 -
Choose menu “
System Tools
”, and you can see the submenus under the main menu:
Time
Settings
,
Diagnostic
,
Firmware Upgrade
,
Factory Defaults
,
Backup & Restore
,
Reboot,
Password
,
System Log
and
Statistics.
Click any of them, and you will be able to configure the
corresponding function. The detailed explanations for each submenu are provided below.
4.21.1 Time Setting
Choose menu “
System Tools
→
Time Setting
”, and then you can configure the time on the
following screen.
Figure 4-119 Time settings
Time Zone -
Select your local time zone from this pull down list.
Date -
Enter your local date in MM/DD/YY into the right blanks.
Time -
Enter your local time in HH/MM/SS into the right blanks.
NTP Server I / NTP Server II -
Enter the address or domain of the
NTP Server I
or
NTP
Server II
, and then the Router will get the time from the NTP Server preferentially. In addition,
the Router built-in some common NTP Servers, so it can get time automatically once it
connects the Internet.
Enable Daylight Saving -
Check the box to enable the Daylight Saving function.
Start -
The time to start the Daylight Saving. Select the month in the first field, the week in the
second field, the day in the third field and the time in the last field.
End -
The time to end the Daylight Saving. Select the month in the first field, the week in the
second field, the day in the third field and the time in the last field.

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top