TP-Link TL-WDR4300 Router Manual PDF (Setup & Configuration Guide)

Page 51 / 146 Scroll up to view Page 46 - 50

TL-WDR4300

N750 Wireless Dual Band Gigabit Router

- 41 -

Figure 4-21 WPA/WPA2 – Personal

•

PSK Password -

You can enter ASCII characters between 8 and 63 characters or 8 to 64

Hexadecimal characters. The default password is the same with the default PIN code,

which is labeled on the bottom of the Router or can be found in Figure 4-16.

•

Group Key Update Period -

Specify the group key update interval in seconds. The value

should be 30 or above. Enter 0 to disable the update.



WPA/WPA2- Enterprise -

It’s based on Radius Server.

•

Version

-

you can choose the version of the WPA security on the drop-down list. The

default setting is

Automatic

, which can select

WPA (

Wi-Fi Protected Access) or

WPA2

(

WPA version 2) automatically based on the wireless station's capability and request.

•

Encryption -

You can select either

Automatic

, or

TKIP

or

AES.



Note:

If you check the

WPA/WPA2-Enterprise

radio button and choose TKIP encryption, you will

find a notice in red as shown in Figure 4-22.

Figure 4-22 WPA/WPA2 - Enterprise

•

Radius Server IP -

Enter the IP address of the Radius server.

•

Radius Port -

Enter the port number of the Radius server.

•

Radius Password -

Enter the password for the Radius server.

•

Group Key Update Period -

Specify the group key update interval in seconds. The value

should be 30 or above. Enter 0 to disable the update.



WEP -

It is based on the IEEE 802.11 standard. If you check this radio button, you will find a

notice in red as show in Figure 4-23.

Page 52 / 146

TL-WDR4300

N750 Wireless Dual Band Gigabit Router

- 42 -

Figure 4-23 WEP

•

Type

-

you can choose the type for the WEP security on the drop-down list. The default

setting is

Automatic

, which can select

Shared Key

or

Open System

authentication type

automatically based on the wireless station's capability and request.

•

WEP Key Format

-

Hexadecimal

and

ASCII

formats are provided here

.

Hexadecimal

format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified

length.

ASCII

format stands for any combination of keyboard characters in the specified

length.

•

WEP Key

-

Select which of the four keys will be used and enter the matching WEP key that

you create. Make sure these values are identical on all wireless stations in your network.

•

Key Type

-

You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for

encryption. "Disabled" means this WEP key entry is invalid.

64-bit -

You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 5 ASCII characters.

128-bit -

You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 13 ASCII characters.

152-bit -

You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is

not promoted) or 16 ASCII characters.



Note:

If you do not set the key, the wireless security function is still disabled even if you have

selected Shared Key as Authentication Type.

Be sure to click the

Save

button to save your settings on this page.

4.6.4

Wireless MAC Filtering

Choose menu “

Wireless 2.4GHz

→

Wireless MAC Filtering

”, you can control the wireless

access by configuring the

Wireless MAC Filtering

function, shown in Figure 4-24.

Page 53 / 146

TL-WDR4300

N750 Wireless Dual Band Gigabit Router

- 43 -

Figure 4-24 Wireless MAC Filtering

To filter wireless users by MAC Address, click

Enable

. The default setting is

Disabled

.



MAC Address

-

The wireless station's MAC address that you want to filter.



Status

-

The status of this entry, either

Enabled

or

Disabled

.



Description -

A simple description of the wireless station.

To Add a Wireless MAC Address filtering entry, click the

Add New…

button. The "

Add or Modify

Wireless MAC Address Filtering entry

"

page will appear, shown in Figure 4-25:

Figure 4-25 Add or Modify Wireless MAC Address Filtering entry

To add or modify a MAC Address Filtering entry, follow these instructions:

1.

Enter the appropriate MAC Address into the

MAC Address

field. The format of the MAC

Address

is

XX-XX-XX-XX-XX-XX

(X

is

any

hexadecimal

digit).

For

example:

00-0A-EB-B0-00-0B.

2.

Give a simple description for the wireless station in the

Description

field. For example:

Wireless station A.

3.

Select

Enabled

or

Disabled

for this entry on the

Status

drop-down list.

4.

Click the

Save

button to save this entry.

To modify or delete an existing entry:

1.

Click the

Modify

in the entry you want to modify. If you want to delete the entry, click the

Delete

.

Page 54 / 146

TL-WDR4300

N750 Wireless Dual Band Gigabit Router

- 44 -

2.

Modify the information.

3.

Click the

Save

button.

Click the

Enable All

button to make all entries enabled

Click the

Disabled All

button to make all entries disabled.

Click the

Delete All

button to delete all entries.

Click the

For example:

If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and

the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all

the other wireless stations cannot access the Router, you can configure the

Wireless MAC

Address Filtering

list by following these steps:

1. Click the

Enable

button to enable this function.

2. Select the radio button “

Allow the entries specified by any enabled entries in the list to

access

” for

Filtering Rules

.

3.

Delete all or disable all entries if there are any entries already.

4. Click the

Add New...

button.

1)

Enter the MAC address

00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F

in the

MAC Address

field.

2)

Enter wireless station A/B in the

Description

field.

3)

Select

Enabled

in the

Status

drop-down list.

4)

Click the

Save

button.

5)

Click the

Back

button.

The filtering rules that configured should be similar to the following list:

4.6.5

Wireless Advanced

Choose menu “

Wireless 2.4GHz

→

Wireless Advanced

”, you can configure the advanced

settings of your wireless network.

Page 55 / 146

TL-WDR4300

N750 Wireless Dual Band Gigabit Router

- 45 -

Figure 4-26 Wireless Advanced



Transmit Power -

Here you can specify the transmit power of Router. You can select High,

Middle or Low which you would like. High is the default setting and is recommended.



Beacon Interval -

Enter a value between 20-1000 milliseconds for Beacon Interval here.

The beacons are the packets sent by the Router to synchronize a wireless network. Beacon

Interval value determines the time interval of the beacons. The default value is 100.



RTS Threshold -

Here you can specify the RTS (Request to Send) Threshold. If the packet

is larger than the specified RTS Threshold size, the Router will send RTS frames to a

particular receiving station and negotiate the sending of a data frame. The default value is

2346.



Fragmentation Threshold -

This value is the maximum size determining whether packets

will be fragmented. Setting the Fragmentation Threshold too low may result in poor network

performance because of excessive packets. 2346 is the default setting and is

recommended.



DTIM Interval -

This value determines the interval of the Delivery Traffic Indication Message

(DTIM). A DTIM field is a countdown field informing clients of the next window for listening to

broadcast and multicast messages. When the Router has buffered broadcast or multicast

messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can

specify the value between 1-15 Beacon Intervals. The default value is 1, which indicates the

DTIM Interval is the same as Beacon Interval.



Enable WMM - WMM

function can guarantee the packets with high-priority messages being

transmitted preferentially. It is strongly recommended.



Enable Short GI -

This function is recommended for it will increase the data capacity by

reducing the guard interval time

.



Enabled AP Isolation -

This function can isolate wireless stations on your network from

each other. Wireless devices will be able to communicate with the Router but not with each

other. To use this function, check this box. AP Isolation is disabled by default.

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share