TP-Link TL-WDR3600 Router Manual PDF (Setup & Configuration Guide)

Page 56 / 145 Scroll up to view Page 51 - 55

TL-WDR3600

N600 Wireless Dual Band Gigabit Router

- 46 -

There are five submenus under the Wireless menu (shown in Figure 4-13):

Wireless Settings

,

WPS

,

Wireless Security

,

Wireless MAC Filtering

,

Wireless Advanced

and

Wireless

Statistics

. Click any of them, and you will be able to configure the corresponding function.

4.7.1

Wireless Settings

Choose menu “

Wireless 5GHz

→

Wireless Settings

”, you can configure the basic settings for

the wireless network of 5GHz on this page.

Figure 4-29 Wireless Settings – 5GHz



Wireless Network Name -

Also called the SSID (Service Set Identification). Enter a value of

up to 32 characters. The same name must be assigned to all wireless devices in your

network. Considering your wireless network security, the default SSID is set to be

TP-LINK_5GHz_XXXXXX. This value is case-sensitive. For example,

TEST

is NOT the

same as

test

.



Region

-

Select your region from the drop-down list. This field specifies the region where the

wireless function of the Router can be used. It may be illegal to use the wireless function of

the Router in a region other than one of those specified in this field. If your country or region

is not listed, please contact your local government agency for assistance.

When you select your local region from the drop-down list, click the

Save

button

,

then the

Note Dialog appears. Click

OK

.

Note Dialog

Page 57 / 145

TL-WDR3600

N600 Wireless Dual Band Gigabit Router

- 47 -



Note:

Limited by local law regulations, version for North America does not have region selection

option.



Mode -

Select the desired mode.



11a only -

Select if all of your wireless clients are 802.11a. When 802.11a mode is

selected, only 802.11a wireless stations can connect to the Router.



11n only-

Select only if all of your wireless clients are 802.11n. When 802.11n mode is

selected, only 802.11n wireless stations can connect to the Router.



11an mixed -

Select if you are using both 802.11a and 802.11n wireless clients. It is

strongly recommended that you set the Mode

11an mixed

, and all of 802.11a and

802.11n wireless stations can connect to the Router.



Channel width -

Select the channel width from the drop-down list

.

The default setting is

automatic, which can adjust the channel width for your clients automatically.



Note:

If

11a only

is selected in the

Mode

field, the

Channel Width

selecting field will turn grey and

the value will become 20M, which is unable to be changed.



Channel -

This field determines which operating frequency will be used. The default channel

is set to

Auto

, so the Router will choose the best channel automatically. It is not necessary

to change the wireless channel unless you notice interference problems with another nearby

access point.



Enable SSID Broadcast -

When wireless clients survey the local area for wireless networks

to associate with, they will detect the SSID broadcast by the Router. If you select the

Enable

SSID Broadcast

checkbox, the Wireless Router will broadcast its name (SSID) on the air.



Enable WDS Bridging -

Check this box to enable WDS. With this function, the Router can

bridge two or more Wlans. If this checkbox is selected, you will have to set the following

parameters as shown in Figure 4-30. Make sure the following settings are correct.

Figure 4-30



SSID(to be bridged)

- The SSID of the AP your Router is going to connect to as a client.

You can also use the search function to select the SSID to join.

Page 58 / 145

TL-WDR3600

N600 Wireless Dual Band Gigabit Router

- 48 -



BSSID(to be bridged)

- The BSSID of the AP your Router is going to connect to as a

client. You can also use the search function to select the BSSID to join.



Survey

- Click this button, you can search the AP which runs in the current channel.



Key type

- This option should be chosen according to the AP's security configuration. It

is recommended that the security type is the same as your AP's security type



WEP Index

- This option should be chosen if the key type is WEP(ASCII) or

WEP(HEX).It indicates the index of the WEP key.



Auth Type

- This option should be chosen if the key type is WEP(ASCII) or

WEP(HEX).It indicates the authorization type of the Root AP.



Password

- If the AP your Router is going to connect needs password, you need to fill

the password in this blank.

4.7.2

WPS

Choose menu “

Wireless 5GHz

→

WPS

”, you can the screen as shown in Figure 4-31. This

section will guide you to add a new wireless device to an existing network quickly by WPS (Wi-Fi

Protected Setup) function.

Figure 4-31 WPS



WPS Status -

Enable or disable the WPS function here.



Current PIN -

The current value of the Router's PIN is displayed here. The default PIN of the

Router can be found in the label or User Guide.



Restore PIN -

Restore the PIN of the Router to its default.



Gen New PIN -

Click this button, and then you can get a new random value for the Router's

PIN. You can ensure the network security by generating a new PIN.



Add device -

You can add a new device to the existing network manually by clicking this

button.

Page 59 / 145

TL-WDR3600

N600 Wireless Dual Band Gigabit Router

- 49 -

If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless

connection between wireless adapter and Router using either Push Button Configuration (PBC)

method or PIN method.



Note:

To build a successful connection by WPS, you should also do the corresponding configuration of

the new device for WPS function meanwhile.

I.

Use the Wi-Fi Protected Setup Button

Use this method if your client device has a Wi-Fi Protected Setup button.

Step 1:

Press the

WPS/Reset

button on the back panel of the Router, as shown in Figure 4-32.

You can also keep the default WPS status as

Enabled

and click the

Add device

button in

Figure 4-31. Then choose “

Press the button of the new device in two minutes

” and

click

Connect

, shown in Figure 4-33.

Figure 4-32

Figure 4-33 Add A New Device

Step 2:

Press and hold the

WPS

button of the client device directly.

Step 3:

The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup

process.

Step 4:

When the WPS LED is on, the client device has successfully connected to the Router.

Step 5:

Refer back to your client device or its documentation for further instructions.

II.

Enter the client device’s PIN on the Router

Use this method if your client device does not have the WPS button, but has a Wi-Fi Protected

Setup PIN number.

Page 60 / 145

TL-WDR3600

N600 Wireless Dual Band Gigabit Router

- 50 -

Step 1:

Keep the default WPS status as

Enabled

and click the

Add device

button in Figure 4-31,

then Figure 4-34 will appear.

Figure 4-34 Add A New Device

Step 2:

Enter the PIN number from the client device in the field on the above WPS screen. Then

click

Connect

button.

Step 3:

“

Connect successfully

” will appear on the screen of Figure 4-34, which means the client

device has successfully connected to the Router.

III. Enter the Router’s PIN on your client device

Use this method if your client device asks for the Router’s PIN number.

Step 1:

On the client device, enter the PIN number listed on the Router’s Wi-Fi Protected Setup

screen, shown in Figure 4-31 (It is also labeled on the bottom of the Router).

Step 2:

The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected Setup

process.

Step 3:

When the WPS LED is on, the client device has successfully connected to the Router.

Step 4:

Refer back to your client device or its documentation for further instructions.



Note:

1)

The WPS LED on the Router will light green for five minutes if the device has been

successfully added to the network.

2)

The WPS function cannot be configured if the Wireless Function of the Router is disabled.

Please make sure the Wireless Function is enabled before configuring the WPS.

4.7.3

Wireless Security

Choose menu “

Wireless 5GHz

→

Wireless Security

”, you can configure the security settings of

your wireless network.

There are five wireless security modes supported by the Router: WPA-Personal, WPA2-Personal,

WPA-Enterprise, WPA2-Enterprise, and WEP.

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share