1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TL-WA7210N
    5. /
  5. 18
Page 86 / 150 Scroll up to view Page 81 - 85
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access Point User Guide
76
Figure 5-9 PPPoE Advanced Settings
MTU Size
-
The default MTU (Maximum Transmission Unit) size is 1480 bytes, which is
usually fine. For some ISPs, you need modify the MTU. This should not be done unless you
are sure it is necessary for your ISP.
Service Name/AC Name
-
They should not be done unless you are sure it is necessary for
your ISP.
ISP Specified IP Address
- If you know that your ISP does not automatically transmit IP
address to the Device during login, click "
Use the IP Address specified by ISP
" checkbutton
and enter the IP address in dotted-decimal notation, which is provided by your ISP.
Detect Online Interval
- The default value is 0. You can input the value between 0 and 120.
The Device will detect Access Concentrator online every interval seconds. If the value is 0, it
means not detecting.
Use the following DNS Servers
- If your ISP specifies a DNS server IP address for you,
click the checkbox, and fill the
Primary DNS
and
Secondary DNS
blanks below. The
Secondary DNS
is optional. Otherwise, the DNS servers will be assigned dynamically from
ISP.
Primary DNS
- (Optional) Enter the DNS IP address in dotted-decimal notation provided by
your ISP.
Secondary DNS
- (Optional) Enter another DNS IP address in dotted-decimal notation
provided by your ISP.
Note:
The new advanced PPPoE parameters will not take effect until you dial-up again.
Click the
Save
button to save your settings.
Click the
Back
button when finished.
4.
If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select
BigPond
Cable
option. And then you should enter the following parameters as in Figure 5-10.
Page 87 / 150
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access Point User Guide
77
Figure 5-10 WAN – BigPond Cable
User Name/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Auth Server -
Enter the authenticating server IP address or host name.
Auth Domain -
Type in the domain suffix server name based on your location.
NSW / ACT -
nsw.bigpond.net.au
VIC / TAS / WA / SA / NT -
vic.bigpond.net.au
QLD -
qld.bigpond.net.au
MTU Size -
The normal
MTU
(Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. It is not recommended that you change the default
MTU Size
unless required
by your ISP.
Connect on Demand -
In this mode, the Internet connection can be terminated automatically
after a specified inactivity period (
Max Idle Time
) and
be
re-established when you attempt to
access the Internet again.
If you want your Internet connection keeps active all the time,
please enter “0” in the
Max Idle Time
field.
Otherwise, enter the number of minutes you want
to have elapsed before your Internet access disconnects.
Connect Automatically -
The connection can be re-established automatically when it was
down.
Connect Manually -
You can click the
Connect
/
Disconnect
button to connect/disconnect
immediately.
This mode also supports the
Max Idle Time
function as
Connect on Demand
mode. The Internet connection can be disconnected automatically after a specified inactivity
period and
re-established when you attempt to access the Internet again.
Click the
Connect
button to connect immediately. Click the
Disconnect
button to disconnect
immediately.
Page 88 / 150
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access Point User Guide
78
Note:
Sometimes the connection cannot be terminated although you specify a time to Max Idle Time
because some applications are visiting the Internet continually in the background.
Click the
Save
button to save your settings.
5.
If your ISP provides L2TP connection, please select
L2TP/Russia L2TP
option. Then you
should enter the following parameters in Figure 5-11.
Figure 5-11 WAN – L2TP/Russia L2TP
User Name/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Dynamic IP/ Static IP -
Choose either one as you are given by your ISP. Click the
Connect
button to connect immediately. Click the
Disconnect
button to disconnect immediately.
Connect on Demand -
You can configure the Device to disconnect from your Internet
connection after a specified period of inactivity (
Max Idle Time
). If your Internet connection
has been terminated due to inactivity,
Connect on Demand
enables the Device to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate
Connect on Demand
, check the radio button. If you want your
Internet connection to remain active at all time, enter 0 in the
Max Idle Time
field. Otherwise,
enter the number of minutes you want to have elapsed before your Internet connection
terminates.
Connect Automatically -
Connect automatically after the Device is disconnected. To use
this option, check the radio button.
Page 89 / 150
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access Point User Guide
79
Connect Manually -
You can configure the Device to make it connect or disconnect
manually. After a specified period of inactivity (
Max Idle Time
), the Device will disconnect
from your Internet connection, and you will not be able to re-establish your connection
automatically as soon as you attempt to access the Internet again. To use this option, check
the radio button. If you want your Internet connection to remain active at all time, enter "0" in
the
Max Idle Time
field. Otherwise, enter the number of minutes that you wish to have the
Internet connecting last unless a new link is requested.
Note:
Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time
,
because some applications are visiting the Internet continually in the background.
Click the
Save
button to save your settings.
6.
If your ISP provides PPTP connection, please select
PPTP/Russia PPTP
option. And you
should enter the following parameters (Figure 5-12):
Figure 5-12
WAN – PPTP/Russia PPTP
User Name/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Dynamic IP/ Static IP -
Choose either as you are given by your ISP and enter the ISP’s IP
address or the domain name.
If you choose static IP and enter the domain name, you should also enter the DNS
assigned by your ISP. And click the
Save
button.
Click the
Connect
button to connect immediately. Click the
Disconnect
button to
disconnect immediately.
Page 90 / 150
TL-WA7210N
2.4GHz 150Mbps Outdoor Wireless Access Point User Guide
80
Connect on Demand -
You can configure the Device to disconnect from your Internet
connection after a specified period of inactivity (
Max Idle Time
). If your Internet connection
has been terminated due to inactivity,
Connect on Demand
enables the Device to
automatically re-establish your connection as soon as you attempt to access the Internet
again. If you wish to activate
Connect on Demand
, check the radio button. If you want your
Internet connection to remain active at all times, enter “0” in the
Max Idle Time
field.
Otherwise, enter the number of minutes you want to have elapsed before your Internet
connection terminates.
Connect Automatically -
Connect automatically after the Device is disconnected. To use
this option, check the radio button.
Connect Manually -
You can configure the Device to make it connect or disconnect
manually. After a specified period of inactivity (
Max Idle Time
), the Device will disconnect
from your Internet connection, and you will not be able to re-establish your connection
automatically as soon as you attempt to access the Internet again. To use this option, click
the radio button. If you want your Internet connection to remain active at all times, enter "0" in
the
Max Idle Time
field. Otherwise, enter the number in minutes that you wish to have the
Internet connecting last unless a new link is requested.
Note:
Sometimes the connection cannot be disconnected although you specify a time to
Max Idle Time
because some applications are visiting the Internet continually in the background.
Click the
Save
button to save your settings.
5.6.2
MAC Clone
MAC Clone allows you to clone the MAC address of the managing PC’s adapter to the WAN port.
This is because some ISPs require that you register the MAC address of your adapter. Usually,
you do not need to change anything here.
Selecting
Network > MAC Clone
will enable you to configure the MAC address of the WAN port
on this page as shown in Figure 5-13.
Figure 5-13
MAC Address Clone
Some ISPs require that you register the MAC Address of your adapter, which is connected to your
cable/DSL Modem or Ethernet during installation. Changes are rarely needed here.
WAN MAC Address -
This field displays the current MAC address of the WAN port, which is
used for the WAN port. If your ISP requires that you register the MAC address, please enter
the correct MAC address into this field. The format for the MAC Address is
XX-XX-XX-XX-XX-XX (X is any hexadecimal digit).
Your PC's MAC Address -
This field displays the MAC address of the PC that is managing
the router. If the MAC address is required, you can click the
Clone MAC Address
button and
this MAC address will fill in the
WAN MAC Address
field.
Click
Restore Factory MAC
to restore the MAC address of WAN port to the factory default value.

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top