Page 16 / 28
Scroll up to view Page 11 - 15
11
Gigabit Load Balance Broadband Router
Use Lightning Arrester
21´
Power lightning arrester and signal lightning arrester are used for lighting protection.
Power lightning arrester is used for limiting the voltage surge due to a lightning. If an
outdoor AC power cord should be directly connected to the device, please use a power
lightning arrester.
Note:
Power lightning arrester is not provided with our product. If needed, please self
purchase it.
Signal lightning arrester is used to protect RJ45 ports of the device from lightning.
When cabling outdoors, please install a signal lightning arrester before connecting the
cable to the device.
When purchasing or using a signal lightning arrester, please observe the following
rules:
The port rate of the signal lightning arrester should match the rate of the desired port
■
on the device. If it is not matched, this signal lighting arrester will not work. Purchase
a standard lightning arrester.
Install signal lightning arrester near the protected device and connect it to the ground
■
via a shorter ground cable.
Equipotential Bonding Cable
Grounding Terminal
Ethernet Cable
Signal Lightning Arrester
Device
Lightning Arrester Connection
Figure 3-4
Note:
Signal lightning arrester is not provided with our product. If needed, please self
purchase it.
Lightning Protection
Page 17 / 28
12
Gigabit Load Balance Broadband Router
Connection
Cha±ter ´
WAN Port
´1²
Please connect the WAN port of the router to the interface provided by ISP via Ethernet
cable.
LAN Port
´1³
Connect a LAN port of the router to the computer by RJ45 cable as the following figure
shown.
LAN Port
RJ45 Cable
RJ45 Port
Connecting the LAN Port
Figure 4-1
Note:
If the router is connecting with Server/Switch or other Ethernet devices, please
make sure the RJ45 cable is less than 100m.
Console Port
´12
CLI (Command Line Interface± enables you to do some simple operations to the router,
thus you can load the CLI after connecting the PCs or Terminals to the console port on
the router via the provided cable.
Connect the console port of the device with your computer by the console cable as the
following figure shown.
Connection
Page 18 / 28
13
Gigabit Load Balance Broadband Router
Connection
Connecting the Console Port
Figure 4-2
You can also manage the device through the console port, for details please refer to the
User Guide on the resource CD.
Note:
The console port is the first port on the right of the front panel.
■
Please keep the device power off when you plugging the console cable.
■
Do not connect the console port with other ports by RJ45 cable.
■
Verify Installation
´1´
After completing the installation, please verify the following items:
There are 5~10cm of clearance around the sides of the device for ventilation and the
■
air flow is adequate.
The voltage of the power supply meets the requirement of the input voltage of the
■
device.
The power socket, device and rack are well grounded.
■
The device is correctly connected to other network devices.
■
Power On
´14
Plug in the negative connector of the provided power cord into the power socket of the
device, and the positive connector into a power outlet as the following figure shown.
Connecting to Power Supply
Figure 4-3
Page 19 / 28
14
Gigabit Load Balance Broadband Router
Connection
Note:
The figure is to illustrate the application and principle. The power plug you get
from the package and the socket in your situation will comply with the regulation in
your country, so they may differ from the figure above.
Initialization
´1µ
After the device is powered on, it begins the Power-On Self-Test. A series of tests
run automatically to ensure the device functions properly. During this time, its LED
indicators will respond as follows:
The Power LED will light on all the time.
■
All LEDs except PWR LED will flash momentarily and then turn off.
■
The SYS LED flashes every second continuously, which means the initialization is
■
finished.
Page 20 / 28
15
Gigabit Load Balance Broadband Router
Configuration
Cha±ter 4
Pre±arations
41²
Connect a PC to a LAN port of the router with a RJ45 cable properly.
1.
Set the Internet Protocol (TCP/IP± properties of the PC as the following figure shown.
2.
Internet Protocol (TCP/IP± Properties
Figure 5-1
Login
41³
To access the GUI (Graphical User Interface± of the router, open a web browser and
1.
browser, then press the Enter key.
Web Browser
Figure 5-2
Enter admin for the default User Name and Password, both in lower case letters.
2.
Then click the Login button or press the Enter key.
Configuration
19216811.live