1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. TD-W8980
    5. /
  5. 23
Page 111 / 117 Scroll up to view Page 106 - 110
TD-W8980
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
102
)
Note:
1)
New firmware versions are posted at http://www.tp-link.com and can be downloaded for free.
There is no need to upgrade the firmware unless the new firmware has a new feature you
want to use. However, when experiencing problems caused by the modem router rather than
the configuration, you can try to upgrade the firmware.
2)
When you upgrade the modem router's firmware, you may lose its current configurations, so
before upgrading the firmware please write down some of your customized settings to avoid
losing important settings.
3)
Do not turn off the modem router or press the Reset button while the firmware is being
upgraded. Loss of power during the upgrade could damage the modem router.
4)
The firmware version must correspond to the hardware.
5)
The upgrade process takes a few moments and the modem router restarts automatically
when the upgrade is complete.
4.21.9 Reboot
Choose menu “
System Tools
”
→
“
Reboot
”, and then you can click the
Reboot
button to reboot
the modem router via the next screen.
Figure 4-108
Some settings of the modem router will take effect only after rebooting, which include
•
Change the LAN IP Address (system will reboot automatically).
•
Change the DHCP Settings.
•
Change the Wireless configurations.
•
Change the Web Management Port.
•
Upgrade the firmware of the modem router (system will reboot automatically).
•
Restore the modem router's settings to factory defaults (system will reboot
automatically).
•
Update the configuration with the file (system will reboot automatically.
4.21.10 Statistics
Choose menu “
System Tools
”
→
“
Statistics
”, and then you can view the statistics of the Modem
router, including total traffic and current traffic of the last Packets Statistic Interval.
Page 112 / 117
TD-W8980
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
103
Figure 4-109
¾
Statistics Status:
Enable or Disable. The default value is disabled. To enable it, click the
Enable
. If it is disabled, the function of DoS protection in Security settings will be disabled.
¾
Statistics Interval (5-60):
The default value is 10. Select a value between 5 and 60 seconds
in the drop-down list. The Packets Statistic interval indicates the time section of the packets
statistic.
Click
Reset
All
to reset the values of all the entries to zero.
Click
Delete
All
to delete all entries in the table.
Click the
Refresh
button to refresh immediately.
Statistics Table:
IP/MAC Address
The IP and MAC address are displayed with related statistics.
Packets
The total number of packets received and transmitted by the modem router.
Total
Bytes
The total number of bytes received and transmitted by the modem router.
Packets
The total number of packets received and transmitted in the last Packets
Statistic interval seconds.
Bytes
The total number of bytes received and transmitted in the last Packets
Statistic interval seconds.
ICMP Tx
The number of the ICMP packets transmitted to WAN per second at the
specified Packets Statistics interval. It is shown like “current transmitting rate
/ Max transmitting rate”.
UDP Tx
The number of UDP packets transmitted to the WAN per second at the
specified Packets Statistics interval. It is shown like “current transmitting rate
/ Max transmitting rate”.
Current
SYN Tx
The number of TCP SYN packets transmitted to the WAN per second at the
specified Packets Statistics interval. It is shown like “current transmitting rate
/ Max transmitting rate”.
Reset
Reset the value of he entry to zero.
Operation
Delete
Delete the existing entry in the table.
Page 113 / 117
TD-W8980
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
104
Appendix A: Specifications
General
Standards and Protocols
ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5,
IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE
802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT
Safety & Emission
FCC, CE
Ports
Four 10/100/1000M Auto-Negotiation RJ45 ports
（
Auto MDI/MDIX)
One RJ11 port
Two USB 2.0 ports
LEDs
Power,
ADSL,
Internet,
Wireless 2.4GHz,
Wireless 5GHz,
WPS,
USB,
1,2,3,4(LAN),
(USB on the back panel)
Network Medium
10Base-T:
UTP category 3, 4, 5 cable
100Base-TX: UTP category-5
1000Base-TX: UTP category-5
Max line length: 6.5Km
Data Rates
Downstream: Up to 24Mbps
Upstream: Up to 1Mbps
System Requirement
Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
Win 9x/ ME/ 2000/ XP/ Vista/ 7
Physical and Environment
Working Temperature
0
~ 40
℃
℃
Working Humidity
10% ~ 90% RH (non-condensing)
Storage Temperature
-40
~ 70
℃
℃
Storage Humidity
5% ~ 90% RH (non-condensing)
Page 114 / 117
TD-W8980
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
105
Appendix B: Troubleshooting
T1. How do I restore my modem router’s configuration to its factory default
settings?
With the modem router powered on, press and hold the
RESET
button on the rear panel for 8 to
10 seconds before releasing it.
)
Note
:
Once the modem router is reset, the current configuration settings will be lost and you will need to
re-configure the router.
T2. What can I do if I don’t know or forget my password?
1) Restore the modem router’s configuration to its factory default settings. If you don’t know how
to do that, please refer to
T1
.
2) Use the default user name and password:
admin
,
admin
.
3) Try to configure your modem router once again by following the instructions in
3.2 Quick
Installation Guide.
T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computer’s IP Address.
For Mac OS X
z
Click the
Apple
icon on the upper left corner of the screen.
z
Go to “
System Preferences
->
Network
”.
z
Select
Airport
on the left menu bar, and then click
Advanced
for wireless configuration; or
select
Ethernet
for wired configuration.
z
In the
Con-figure IPv4
box under
TCP/IP
, select
Using DHCP
.
z
Click
Apply
to save the settings.
For Windows 7
z
Click “
Start
->
Control Panel
->
Network and Internet
->
View network status
->
Change
adapter settings
”.
z
Right-click
Wireless Network Connection
(or
Local Area Connection
), and then click
Properties
.
z
Select
Internet Protocol Version 4 (TCP/IPv4)
, and then click
Properties
.
z
Select
Obtain an IP address automatically
and
Obtain DNS server address automatically
.
Then click
OK
.
For Windows XP
z
Click “
Start
->
Control Panel
->
Network and Internet Connections
->
Network
Connections
”.
z
Right-click
Wireless Network Connection
(or
Local Area Connection
), and then click
Properties
.
z
Select
Internet Protocol (TCP/IP)
, and then click
Properties
.
Page 115 / 117
TD-W8980
N600 Wireless Dual Band Gigabit ADSL2+ Modem Router User Guide
106
z
Select
Obtain an IP address automatically
and
Obtain DNS server address automatically
.
Then click
OK
.
For Windows 8
z
Move your mouse to the lower right corner and you will see
Search
icon
in the
Popups. Go
to “
->
Apps
”. Type
Control Panel
in the search box and press
Enter
, then you will go to
Control Panel
.
z
Click “
View network status and tasks
>
Change adapter settings
”.
z
Right-click “
Ethernet
” and then select
Properties
.
z
Double-click
Internet Protocol Version 4 (TCP/IPv4)
. Select
Obtain an IP address
automatically
, choose
Obtain DNS server address automatically
and then click
OK
.
2) Configure your IE browser
Open your IE browser, click
Tools
tab and you will see the
following screen.
Click
Internet Options
Click
OK
Select
Never dial a
connection

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top