Page 41 / 91
Scroll up to view Page 36 - 40
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router User Guide
To configure WEP-64Bits settings, select the WEP-64Bits option from the drop-down list. The
menu will change to offer the appropriate settings. WEP-64Bits is a data privacy mechanism
based on a 64-bit shared key algorithm, as described in the IEEE 802.11g standard.
Figure 4-16
2)
WEP-128Bits
To configure WEP-128Bits settings, select the WEP-128Bits option from the drop-down list.
The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit.
Figure 4-17
3)
WPA-PSK
To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The
menu will change to offer the appropriate settings. WPA-PSK requires a shared key and does
not use a separate server for authentication. PSK keys can be ASCII or Hex type.
33
Page 42 / 91
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router User Guide
Figure 4-18
¾
Encryption:
Select the encryption you want to use: TKIP/AES, TKIP or AES (AES is an
encryption method stronger than TKIP).
•
TKIP
(
T
emporal
K
ey
I
ntegrity
P
rotocol) - a wireless encryption protocol that provides
dynamic encryption keys for each packet transmitted.
•
AES
(
A
dvanced
E
ncryption
S
tandard) - A security method that uses symmetric
128-bit block data encryption.
¾
Pre-Shared Key:
Enter the key shared by the Router and your other network devices. It
must have 8-63 ASCII characters or 64 Hexadecimal digits.
4)
WPA2-PSK
To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The
menu will change to offer the appropriate settings. WPA2-PSK requires a shared key and
does not use a separate server for authentication. PSK keys can be ASCII or Hex type.
Figure 4-19
5)
WPA-PSK/WPA2-PSK
To configure WPA-PSK/WPA2-PSK settings, select the WPA-PSK/WPA2-PSK option from
the
drop-down
list.
The
menu
will
change
to
offer
the
appropriate
settings.
WPA-PSK/WPA2-PSK requires a shared key and does not use a separate server for
authentication. PSK keys can be ASCII or Hex type. WPA-PSK/WPA2-PSK is more flexible
than WPA-PSK or WPA2-PSK.
Figure 4-20
4.3.3.1. WPS Settings
¾
WPS Settings:
WPS can help you to add a new wireless device to an existing network
34
Page 43 / 91
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router User Guide
quickly. This section will guide you how to use WPS function.
•
WPS state:
Display the current WPS state.
•
WPS mode:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can
establish a wireless connection between wireless adapter and Router using either Push
Button Configuration (PBC) method or PIN method, please select the one you want.
•
WPS progress:
Show the current WPS progress.
•
Reset to OOB:
Use this button to reset the WPS state to “unconfigured”, so that a new
key will be created when using WPS function next time.
1)
PBC
If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration
(PBC) method, you can add it to the network by PBC with the following two methods. Click
PBC
, you will see the screen as shown below.
Figure 4-21
Method One:
Step 1:
Press the WPS button on the back panel of the Router or click
Start WPS
button in
Figure 4-21.
Step 2:
Press and hold the WPS button of the adapter directly for 2 or 3 seconds.
Step 3:
Wait for a while until the next screen appears. Click
Finish
to complete the WPS
configuration.
35
Page 44 / 91
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router User Guide
The WPS Configuration Screen of Wireless Adapter
Method Two:
Step 1:
Press the WPS button on the front panel of the Router or click
Start WPS
button in
Figure 4-21.
Step 2:
For the configuration of the wireless adapter, please choose “
Push the button on
my access point
”
in the
configuration utility of the WPS as below, and click
Next
.
36
Page 45 / 91
TD-W8951ND
150Mbps Wireless N ADSL2+ Modem Router User Guide
The WPS Configuration Screen of Wireless Adapter
Step 3:
Wait for a while until the next screen appears. Click
Finish
to complete the WPS
configuration.
The WPS Configuration Screen of Wireless Adapter
2)
PIN code
If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to
the network by PIN with the following two methods. Click
PIN code
, you will see the screen as
shown below.
37
19216811.live