TP-Link Archer VR2600 Router Manual PDF (Setup & Configuration Guide)
Given below is full router user manual of TP-Link Archer VR2600 router model. You can also download this manual in PDF Format to read later on your computer.
Product user manuals come handy in case you want to know all functionalities of your device, troubleshooting, fist time configuration & setup and in many other situations.
Page 1 / 2
Quick Installation Guide
AC2600 Wireless Gigabit VDSL/ADSL Modem Router
7106505864
REV1.0.0
Connect the Hardware
Configure the Modem Router
Enjoy the Internet
VR2600
1
Now you can enjoy your Internet.
If you want more advanced settings, please refer to the User Guide on TP-LINK official website at www.tp-link.com.
3
Push in to turn on
the modem router.
Wired
Wireless
Verify that the following LEDs are on
and stable before continuing with
the configuration.
4
Note: The DSL LED takes about 1 to 2 minutes to stabilize.
Power On
On
DSL
Ethernet Cable
Modem Router
Connecting your computer to the modem router via a wired or wireless
connection
Connect wirelessly by using the SSID
(network name) and Wireless Password
printed on the product label at the bottom of
the modem router.
2
Configuring the modem router via a web browser
http://tplinkmodem.net
High
Middle
Low
Save
Confirm Password
New Password
A
Launch a web browser and type in
http://tplinkmodem.net
or
192.168.1.1
.
Create a new password (1-15 characters) and click
Save
.
Note: If the login page does not appear, please refer to FAQ->Q1.
Select your
Region
and
Time Zone
, then click
Next
. Then follow the step-by-step
instructions of the Quick Setup to complete the initial configuration.
Note: Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region only.
C
Enter the password you set and click
Log in
.
Note: For subsequent logins, you only need to enter the password that you have set to log in.
B
If you don’t need the phone service, just directly connect the
modem router to the phone jack with the provided phone cable,
then follow steps 3 and 4 to complete the hardware connection.
Power Adapter
PHONE
LINE
MODEM
1
DSL Splitter
Phone (Optional)
2
Phone Jack
Phone Cable
Page 2 / 2
Q1. What can I do if the login page does not appear?
A1. If the computer is set to a static or fixed IP address, change it to obtain an IP address
automatically from the modem router.
A2. Verify
http://tplinkmodem.net
is correctly entered in the web browser and press
Enter.
A3. Use another web browser and try again.
A4. Reboot your modem router and try again.
A5. Disable and enable the active network adapter.
Q2. What can I do if the DSL LED
does not turn solid on?
A1. Check your cables and make sure they are all plugged in correctly, including the
telephone lines and power adapter.
A2. Restore your modem router to its factory default settings.
A3. Remove the DSL splitter, directly connect the modem router to the phone jack and
follow this Quick Installation to reconfigure the modem router.
A4. Contact your ISP to verify if the DSL line is in good status.
A5. If you have tried all the suggestions above and the problem still exists, contact our
Technical Support.
Q3. What can I do if I cannot access the Internet?
A1. Make sure the telephone and Ethernet cables are plugged in correctly.
A2. Try to log into the web management page of the modem router using the default address at
http://tplinkmodem.net
. If you can, try the following answers. If you cannot, change your
computer to obtain an IP address automatically from the modem router.
A3. Consult your ISP and make sure all the VPI/VCI (or VLAN ID), Connection Type, account
username and password are correct. If they are not, please replace them with the correct
settings and try again.
A4. Restore the modem router to its factory default settings and reconfigure the modem router
by following the instructions in this Quick Installation Guide.
A5. Please contact our Technical Support if the problem still exists.
Q4. What can I do if I forget my password?
Web Management page password:
Restore the modem router to its factory default settings and then set a new password using 1-15
characters.
Wireless Network password:
A1. The default Wireless Password/PIN is printed on the product label of the modem router.
A2. If the default wireless password has been changed, log into the modem router's web
management page and go to
Basic > Wireless
to retrieve or reset your password.
Q5. How do I restore the modem router to its factory default settings?
A1. With the modem router powered on, press and
hold down the
Reset
button on the rear panel
of the modem router for 8 seconds until all LEDs
turn back on momentarily, then release the
button.
FAQ (Frequently Asked Questions)
LED Indicators
Note: You can turn all lighted LEDs on or off by pressing the LED On/Off button.
LED
Status
Indication
Wireless
5GHz
Wireless
2.4GHz
WPS
LAN
USB
DSL
Internet
Power
System initialization complete.
System initializing or firmware upgrading is in process.
Do not disconnect or power off the modem router.
Power is off.
DSL line is synchronized and ready to use.
The DSL negotiation is in progress.
DSL synchronization failed.
Internet connection is available.
No Internet connection or the modem router is operating in
Bridge mode.
The 2.4GHz wireless radio band is enabled.
The 2.4GHz wireless radio band is disabled.
The 5GHz wireless radio band is enabled.
The 5GHz wireless radio band is disabled.
At least one LAN port is connected.
No LAN port is connected.
Turns On when a WPS synchronization is established and
automatically turns Off about five minutes later.
A wireless device is trying to connect to the network via WPS.
This process may take up to 2 minutes.
The inserted USB device is identified and ready to use.
A new USB device is being identified.
No USB device is plugged into the USB port.
On
Flashing
Off
On
Flashing
Off
On
Off
On
Off
On
Off
On/Off
Slow Flashing
On
Flashing
Off
On
Off
To manage your network conveniently on your mobile device,
19216811.live