TP-Link Archer C20 Router Manual PDF (Setup & Configuration Guide)

Page 26 / 144 Scroll up to view Page 21 - 25

Archer C20

AC750 Wireless Dual Band Router

- 14 -

3) If the connection type detected is

PPPoE/Russia PPPoE

, the next screen will appear as

shown in Figure 3-9. Configure the following parameters and then click

Figure 3-9 Quick Setup – PPPoE/Russia PPPoE



Username

/

Password -

Enter the

Username

and

Password

provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact

your ISP.



Confirm password -

Enter the password again to make sure that the password is

correct.

4) If your connection type is

L2TP/ Russia L2TP

, select L2TP/Russia L2TP in Figure 3-6

and the next screen will appear as shown in Figure 3-10.Configure the following

parameters and then click

Figure 3-10 Quick Setup – L2TP/Russia L2TP



Username

/

Password -

Enter the

Username

and

Password

provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact

your ISP.

Select

Static IP

if the IP Address/ Subnet Mask/ Gateway and DNS server address have

been provided by your ISP. Then please enter server IP address or domain name provided by

your ISP, and also enter the corresponding parameters.

Page 27 / 144

Archer C20

AC750 Wireless Dual Band Router

- 15 -

Select

Dynamic IP

if none of the above parameters are provided. Then you just need to enter

server IP address or domain name provided by your ISP.

5) If your connection type is

PPTP/Russia PPTP

, select PPTP/Russia PPTP in Figure 3-6

and the next screen will appear as shown in Figure 3-11. Configure the following

parameters and then click

Figure 3-11 Quick Setup – PPTP/Russia PPTP



Username

/

Password -

Enter the

Username

and

Password

provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact

your ISP.

Select

Static IP

if the IP Address/ Subnet Mask/ Gateway and DNS server address have

been provided by your ISP. Then please enter server IP address or domain name provided by

your ISP, and also enter the corresponding parameters.

Page 28 / 144

Archer C20

AC750 Wireless Dual Band Router

- 16 -

Select

Dynamic IP

if none of the above parameters are provided. Then you just need to enter

server IP address or domain name provided by your ISP.

5.

After finishing the WAN Connection Type selection, the

Wireless Dual Band Selection

page

will appear as shown in Figure 3-12. Choose the frequency you want for your wireless

network and then click

Figure 3-12 Quick Setup – Dual Band Selection



2.4GHz

- You can use the 2.4GHz band to connect to many classic wireless devices like

gaming consoles, laptops, DVRs, etc.



5GHz

- This band is less crowded and is used for time-sensitive music, video streaming

or gaming. Using this band can avoid interference with 2.4GHz networks or noisy

devices like cordless phones and microwave ovens.

6.

Configure the basic parameters for 2.4GHz wireless network in the following screen as

shown in Figure 3-13, and then click

Page 29 / 144

Archer C20

AC750 Wireless Dual Band Router

- 17 -

Figure 3-13 Quick Setup – Wireless 2.4GHz



Wireless Network Name -

Also called the

SSID (Service Set Identification). Enter a

value of up to 32 characters. The same name must be assigned to all wireless devices

in your network. The default SSID is set to be TP-LINK_XXXX. This value is

case-sensitive. For example,

TEST

is NOT the same as

test

.



Region

-

Select your region from the drop-down list. This field specifies the region

where the wireless function of the router can be used. It may be illegal to use the

wireless function of the router in a region other than one of those specified in this field. If

your country or region is not listed, please contact your local government agency for

assistance.



Note:

Limited by local law regulations, version for North America does not have region

selection option.



Security



Enable Security (WPA-PSK/WPA2-PSK) –

It’s selected by default, with the

default PSK password the same as the default PIN code.



Disable Wireless Security -

The wireless security function can be enabled or

disabled. If disabled, the wireless stations will be able to connect the router without

encryption.

The above settings are only for basic wireless parameters. For advanced settings, please

check “

More Advanced Wireless Settings

”, and then you can set the following parameters.

Page 30 / 144

Archer C20

AC750 Wireless Dual Band Router

- 18 -



Band -

This field displayed the operating frequency being configured.



Mode -

This field determines the wireless mode which the router works on.



11bg mixed -

Select if you are using both 802.11b and 802.11g wireless clients.



11bgn mixed -

Select if you are using a mix of 802.11b, 11g, and 11n wireless

clients.



Channel Width -

Select any channel width from the drop-down list. The default setting

is “Auto”, which can adjust the channel width for your clients automatically.



Channel -

This field determines which operating frequency will be used. It is not

necessary to change the wireless channel unless you notice interference problems with

another nearby access point. If you select “Auto”, then the AP will select the best

channel automatically.

7.

Configure the basic parameters for 5GHz wireless network in the following screen as shown

in Figure 3-14, and then click

Figure 3-14 Quick Setup – Wireless 5GHz



Wireless Network Name -

Also called the

SSID (Service Set Identification). Enter a

value of up to 32 characters. The same name must be assigned to all wireless devices

in your network. The default SSID is set to be TP-LINK_XXXX_5G. This value is

case-sensitive. For example,

TEST

is NOT the same as

test

.

Rate

Popular TP-Link Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share