1. Home
    2. /
  2. Manuals
    3. /
  3. TP-Link
    4. /
  4. Archer C2
    5. /
  5. 8
Page 36 / 143 Scroll up to view Page 31 - 35
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 26 -
Figure 4-5 WAN - PPPoE
Username/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Secondary Connection
-
It’s available only for PPPoE Connection. If your ISP provides an
extra Connection type such as Dynamic/Static IP to connect to a local area network, then you
can check the radio button of Dynamic/Static IP to activate this secondary connection.
Disabled
-
The Secondary Connection is disabled by default, so there is PPPoE
connection only. This is recommended.
Dynamic IP
-
You can check this radio button to use Dynamic IP as the secondary
connection to connect to the local area network provided by ISP.
Static IP
-
You can check this radio button to use Static IP as the secondary connection
to connect to the local area network provided by ISP.
Always on -
In this mode, the Internet connection will be active all the time.
Connect on Demand -
In this mode, the Internet connection can be terminated automatically
after a specified inactivity period (
Max Idle Time
) and be re-established when you attempt to
access the Internet again. If you want your Internet connection keeps active all the time,
please enter “0” in the
Max Idle Time
field. Otherwise, enter the number of minutes you want
to have elapsed before your Internet access disconnects.
Page 37 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 27 -
Connect Manually -
You can click the Connect/Disconnect button to connect/disconnect
immediately. This mode also supports the
Max Idle Time
function as Connect on Demand
mode. The Internet connection can be disconnected automatically after a specified inactivity
period and re-established when you attempt to access the Internet again.
Click the
Connect
button to connect immediately. Click the
Disconnect
button to disconnect
immediately.
Caution
: Sometimes the connection cannot be terminated although you specify a time to Max Idle
Time because some applications are visiting the Internet continually in the background.
If you want to do some advanced configurations, please click the
Advanced
button, and the page
shown in Figure 4-6 will then appear:
Figure 4-6 PPPoE Advanced Settings
Service Name/Server Name -
The service name and server name should not be configured
unless you are sure it is necessary for your ISP.
In most cases, leaving these fields blank will
work.
MTU(Bytes) -
The default MTU size is “1480” bytes, which is usually fine. It is not
recommended that you change the default
MTU Size
unless required by your ISP.
Enable Fullcone NAT -
It is a type of NAT, if not enabled, the default NAT will act.
Enable IGMP Proxy
-
IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is enabled, and if you are not
sure, please contact your ISP or just leave it.
ISP Specified IP Address -
If your ISP does not automatically assign IP addresses to the
router during login, please click “
Use IP address specified by ISP
” check box and enter the
IP address provided by your ISP in dotted-decimal notation.
Page 38 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 28 -
Detect Online Interval -
The router will detect Access Concentrator online at every interval.
The default value is “0”. You can input the value between “0” and “120”. The value “0”
means
no detect.
Primary DNS/Secondary DNS -
If your ISP does not automatically assign DNS addresses to
the router during login, please click “
Set DNS server manually
” check box and enter the IP
address of your ISP’s primary DNS server. If a secondary DNS server address is available,
enter it as well.
Click the
Save
button to save your settings.
4.
If your ISP provides BigPond Cable (or Heart Beat Signal) connection, please select
BigPond Cable
. And you should enter the following parameters (Figure 4-7):
Figure 4-7 WAN - BigPond Cable
Username/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Auth Server -
Enter the authenticating server IP address or host name.
Auth Domain -
Type in the domain suffix server name based on your location.
e.g.
Page 39 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 29 -
NSW / ACT -
nsw.bigpond.net.au
VIC / TAS / WA / SA / NT -
vic.bigpond.net.au
QLD -
qld.bigpond.net.au
MTU(Bytes)-
The normal
MTU
(Maximum Transmission Unit) value for most Ethernet
networks is 1500 Bytes. It is not recommended that you change the default
MTU
value unless
required by your ISP.
Enable IGMP Proxy
-
IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is enabled, and if you are not
sure, please contact your ISP or just leave it.
Always on -
In this mode, the Internet connection will be active all the time.
Connect on Demand -
In this mode, the Internet connection can be terminated automatically
after a specified inactivity period (
Max Idle Time
) and
be
re-established when you attempt to
access the Internet again. Enter the number of minutes you want to have elapsed before your
Internet access disconnects.
Connect Manually -
You can click the
Connect
/
Disconnect
button to connect/disconnect
immediately.
This mode also supports the
Max Idle Time
function as
Connect on Demand
mode. The Internet connection can be disconnected automatically after a specified inactivity
period and
re-established when you attempt to access the Internet again.
Click the
Connect
button to connect immediately. Click the
Disconnect
button to disconnect
immediately.
Caution
: Sometimes the connection cannot be terminated although you specify a time to Max Idle
Time because some applications are visiting the Internet continually in the background.
Click the
Save
button to save your settings.
5.
If your ISP provides L2TP connection, please select
L2TP/Russia L2TP
option. And you
should enter the following parameters (Figure 4-8):
Page 40 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 30 -
Figure 4-8 WAN - L2TP/Russia L2TP
UserName/Password -
Enter the User Name and Password provided by your ISP. These
fields are case-sensitive.
Addressing Type -
Choose the addressing type given by your ISP, either Dynamic IP or
Static IP. Click the
Connect
button to connect immediately. Click the
Disconnect
button to
disconnect immediately.
MTU(Bytes) -
The default MTU size is “1460” bytes, which is usually fine. It is not
recommended that you change the default
MTU Size
unless required by your ISP.
Enable IGMP Proxy
-
IGMP (Internet Group Management Protocol) is used to manage
multicasting on TCP/IP networks. Some ISPs use IGMP to perform remote configuration for
client devices, such as the modem router. The default value is enabled, and if you are not
sure, please contact your ISP or just leave it.
Always on -
In this mode, the Internet connection will be active all the time.
Connect on Demand -
You can configure the router to disconnect from your Internet
connection after a specified period of inactivity (
Max Idle Time
). If your Internet connection
has been terminated due to inactivity,
Connect on Demand
enables the router to
automatically re-establish your connection as soon as you attempt to access the Internet

Rate

3.5 / 5 based on 2 votes.

Popular TP-Link Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top