Page 136 / 143
Scroll up to view Page 131 - 135
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 126 -
Figure A-4 Virtual Servers
Figure A-5 Add or Modify a Virtual server Entry
Note:
Your opposite side should call your WAN IP, which is displayed on the “Status” page.
4)
How to enable DMZ Host: Log in to the router, click the “
Forwarding
” menu on the left of
your browser, and click "
DMZ
" submenu. On the "DMZ" page, click
Enable
radio button
and type your IP address into the “DMZ Host IP Address” field, using
192.168.0.169 as
an example, remember to click the
Save
button.
Figure A-6 DMZ
5)
How to enable H323 ALG: Log in to the router, click the “
Security
” menu on the left of
your browser, and click “
Basic Security
” submenu. On the “
Basic Security
” page,
check the
Enable
radio button next to
H323 ALG
. Remember to click the
Save
button.
Page 137 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 127 -
Figure A-7 Basic Security
4.
I want to build a WEB Server on the LAN, what should I do?
1)
Because the WEB Server port 80 will interfere with the WEB management port 80 on the
router, you must change the WEB management port number to avoid interference.
2)
To change the WEB management port number: Log in to the router, click the “
Security
”
menu on the left of your browser, and click "
Remote Management
" submenu. On the
"
Remote Management
" page, type a port number except 80, such as 88, into the "Web
Management Port" field. Click
Save
and reboot the router.
Figure A-8 Remote Management
Note:
If the above configuration takes effect, you can visit and configure the router by typing
(the router’s LAN IP address: Web Management Port) in the address
Page 138 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 128 -
field of the Web browser. If the LAN IP of the modem connected with your router is
192.168.0.x, the default LAN IP of the router will automatically switch from
192.168.0.1 to
192.168.1.1 to avoid IP conflict; in this case, please try
.
3)
Log in to the router, click the “
Forwarding
” menu on the left of your browser, and click
the "
Virtual Servers
" submenu. On the "
Virtual Servers
" page, click
Add New
, then on
the “
Add or Modify a Virtual Server
” page, enter “80” into the blank next to the “
Service
Port
”, and your IP address next to the “
IP Address
example, remember to
Enable
and
Save
.
Figure A-9 Virtual Servers
Figure A-10 Add or Modify a Virtual server Entry
5.
The wireless stations cannot connect to the router.
1)
Make sure the "
Wireless Radio Band
" is enabled.
2)
Make sure that the wireless stations' SSID accord with the router's SSID.
3)
Make sure the wireless stations have right KEY for encryption when the router is
encrypted.
4)
If the wireless connection is ready, but you can’t access the router, check the IP Address
of your wireless stations.
Page 139 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 129 -
Appendix B: Configuring the PC
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP.
First make sure your Ethernet Adapter is working, refer to the adapter’s manual if needed.
1.
Install TCP/IP component
1)
On the Windows taskbar, click the
Start
button, point to
Settings
, and then click
Control
Panel
.
2)
Click the
Network and Internet Connections
icon, and then click on the
Network
Connections
tab in the appearing window.
3)
Right click the icon that showed below, select Properties on the prompt page.
Figure B-1
4)
In the prompt page that showed below, double click on the
Internet Protocol (TCP/IP)
.
Figure B-2
Page 140 / 143
Archer C2
AC750 Wireless Dual Band Gigabit Router
- 130 -
5)
The following
TCP/IP Properties
window will display and the
IP Address
tab is open on
this window by default.
6)
Select
Obtain an IP address automatically
and
Obtain DNS server automatically
, as
shown in the Figure below:
Figure B-3
19216811.live