1. Home
    2. /
  2. Manuals
    3. /
  3. Totolink
    4. /
  4. N200RE
    5. /
  5. 2
Page 6 / 37 Scroll up to view Page 1 - 5
5
2.3.2 Rear Panel
The figure below shows the rear panel of the router N200RE.
Power
ON/OFF
The switch allows you to power on or off the router.
DC IN
The Power socket is where you will connect the power adapter.
RST/WPS
RST:
With the router powered on, press
and hold the button until the CPU
LED becomes
quick-flash from slow-flash. And then release the button and
wait the router to reboot to its factory default settings.
WPS:
If you have client devices you can press this button to quickly establish
a router and client devices and automatically configure wireless security for
your wireless network.
WAN
This port is where you will connect the DSL/cable Modem, or Ethernet.
1/2/3/4 LAN
This port connects the router to local PC.
Note:
Press and hold RST/WPS button for about less than 5 seconds and the CPU LED indicator
changes its lighting, it is WPS working. If more than 5 seconds and the CPU LED not response, the
router will reboot to default factory settings.
Page 7 / 37
6
3. HARDWARE INSTALLATION
3.1 Hardware Installation
For those computers you wish to connect with Internet by this router, each of the computers
must be properly connected with the router through provided UTP LAN Cables.
1.
Connect the provided UTP LAN cable to one of the router’s LAN port.
2. Connect the other end of the UTP LAN cable to
your computer’s LAN port.
3.
Connect the second UTP LAN cable to router’s WAN port.
4. Connect the other end of the UTP LAN cable to ADSL or Modem port.
5. Plug the Power Adapter into the Router and then into an outlet.
6. Turn on your computer.
7. Check and confirm that the Power LED and LAN LED on the router are ON.
3.2 Check the Installation
The control LEDs of the WLAN Router are clearly visible and the status of the network link
can be seen instantly:
1. With the power source on, once the device is connected to the broadband modem, the
Power, CPU, LAN, WLAN and WAN port LEDs of the WLAN Router will blinks for one
second indicating a normal status.
2. When the WAN Port is connected to the ADSL/Cable modem, the WAN LED will light up.
3. When the LAN Port is connected to the computer system, the LAN LED will light up.
3.3 Set up the Computer
The default IP address of the Router is 192.168.1.1, the default Subnet Mask is
255.255.255.0. Both of these parameters can be changed as you want. In this guide, we
will use the default values for description.
Connect the local PC to the LAN port on the Router. There are then two ways to configure
the IP address for your PC.
Configure the IP address manually
Configure the network parameters. The IP address is 192.168.1.xxx (“xxx”
range from 2 to
254). The Subnet Mask is 255.255.255.0 and Gateway is 192.168.1.1 (Router’s default IP
address).
Obtain an IP address automatically
Set up the TCP/IP Protocol in
Obtain an IP address automatically
mode on your PC.
Now, you can run the Ping command in the
command prompt
to verify the network
connection between your PC and the Router. Open a command prompt, and type in
ping
192.168.1.1
, then press
Enter.
Page 8 / 37
7
If the result displayed is similar to that shown in above figure, it means that the connection
between your PC and the Router has been established.
If the result displayed is similar to that shown in the above figure, it means that your PC has
not connected to the Router successfully. Please check it following below steps:
1.
Is the connection between your PC and the Router correct?
If correct, the LAN port on the Router and LED on your PC’s adapter should be lit.
2.
Is the TCP/IP configuration for your PC correct?
Since the Router’s IP address is 192.168.1.1, your PC’s IP address must be
within the
range of 192.168.1.2 ~ 192.168.1.254, the Gateway must be 192.168.1.1.
Page 9 / 37
8
4. CONNECTING TO INTERNET
This chapter introduces how to configure the basic functions of your router to access
Internet.
4.1 Accessing Web page
Connect to the Router by typing 192.168.1.1 in the address field of Web Browser. Then
press
Enter
key.
It will show up the following page that requires you to enter valid User Name and Password:
Enter
admin
for User Name and Password, both in lower case letters. Then click
OK
button or press
Enter
key.
Now you will get into the web interface of the device. The Main screen will appear.
Now you have logged into the web interface of the router.
Note:
If the above screen does not prompt, it means that your web-browser has been set to using a
proxy. Go to
Tools menu
>
Internet Options
>
Connections
>
LAN Settings
, in the screen that
appears, cancel the
Using Proxy checkbox
, and click
OK
to finish it.
Page 10 / 37
9
4.2 Changing Password
First, we recommend that you change the password to protect the security of your router.
Please go to
Management
—
Password
change the password required to log into your
Router.
Old Password:
the current password.
New Password:
new password is used for administrator authentication.
Confirm Password:
new password should be re-entered to verify its accuracy.
4.3 Easy Setup
Easy Setup
is provided as part of the web configuration utility. Users can simply finish the
settings on this page to get the Wireless Router ready to access Internet.
Note:
password length is 8 characters maximum, characters after the 8
th
position will be truncated.

Rate

4 / 5 based on 1 vote.

Popular Totolink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top