Page 31 / 90 Scroll up to view Page 26 - 30
Chapter 2: WEB Configuration
Illustrations contained in this document are for representation only.
27
Fig. 8
2.
2.
2.
2. Connection
onnection
onnection
onnection
This page reports current connection status containing startup procedures, downstream and upstream
status, CM online information, and so on. The information can be useful to your cable company’s
support technician if you’re having problems.
Page 32 / 90
Chapter 2: WEB Configuration
Illustrations contained in this document are for representation only.
28
Fig. 9
3.
3.
3.
3.
Password
Password
Password
Password
Forcing end user to change the password
Upon access to the web pages on the CPE side of the router, if the user has not changed the default
web password, a warning message must be displayed in the top banner of the web interface such as
being visible while accessing any tabs.
This warning message informs the user that the default password must be changed:
In
the
second sentence, “here” is a hyperlink to the password setting page. Clicking on “here” lead to the
display of the password setting page.
More information
By default, the username is empty (“”) and the password is “admin”.
This is set by different actions (non exhaustive list):
-
at the manufactory level,
-
following a reset factory on the modem,
-
following a reset from the operator,
-
following a change by the user who wants to come back to the default setting after using its own
settings
When the current password is the default one, the user is strongly encouraged to change the default
web password:
-
Once the user logs in the web pages, the password setting page is displayed
-
the warning message must be displayed in the top banner of the web interface
-
The user can still access to all the web pages even if the password is not changed
-
The warning message must be displayed on the top banner of each accessed Web page while the
password is not changed
-
The password warning message must be visible while accessing all tabs in a the same web page
Page 33 / 90
Chapter 2: WEB Configuration
Illustrations contained in this document are for representation only.
29
-
The password warning message is no more displayed on the banners once the default
password has been replaced by a new one.
At your first connection or while the password is the default one, a warning message is displayed on
the top banner of each Web configuration page. We want to encourage you to change the password in
order to enforce the security of your modem.
The password can be a maximum of 8 characters and is case sensitive. In addition, this page can be
used to restore the gateway to its original factory settings. Use this with caution, as all the settings you
have made will be lost. To perform this reset, set
Restore Factory Defaults
to
Yes
and click
Apply
.
This has the same effect as a factory reset using the rear panel reset switch, where you hold on the
switch for 15 seconds, then release it.
Note: We are always suggesting to modify the password is implementing for Voice Wireless Gateway.
It is a basically protection to access Voice Wireless Gateway.
Fig. 10
To change the password: type the password, and re-enter it again.
If the password is accepted, you are required to re log on the web pages:
Page 34 / 90
Chapter 2: WEB Configuration
Illustrations contained in this document are for representation only.
30
If the password is no accepted, an error message is displayed:
Click on try again.
4.
4.
4.
4. Diagnostics
Diagnostics
Diagnostics
Diagnostics
This page offers basic diagnostic tools for you to utilize when connectivity problems occur. When you
ping an Internet device, you send a packet to its TCP/IP stack, and it sends one back to yours. To use
the ping Test, enter the information needed and press
Start Test
; the Result will be displayed in the
lower part of the window. Press
Abort Test
to stop, and
Clear Results
to clear the result contents.
Note: Firewalls may cause pings to fail but still provide you TCP/IP access to selected devices behind
them. Keep this in mind when pinging a device that may be behind a firewall. Ping is most useful to
verify connectivity with PCs which do not have firewalls, such as the PCs on your LAN side.
Page 35 / 90
Chapter 2: WEB Configuration
Illustrations contained in this document are for representation only.
31
Fig. 11
5.
5.
5.
5. Event Log
Event Log
Event Log
Event Log
This page displays the contents of the SNMP event log. Press “
Clear Log
” button to clear the logs.

Rate

124.8 / 5 based on 304 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top