Thomson TG787 Router Manual PDF (Setup & Configuration Guide)

Page 56 / 88 Scroll up to view Page 51 - 55

E-DOC-CTC-20080118-0051 v2.0

50

4

Getting the Most Out of Your Thomson Gateway

4.3.3

Configuring UPnP on the Thomson Gateway

Introduction

On the

Thomson Gateway Web Interface

you can:

±

Enable/Disable UPnP

±

Extended Security

Enable/Disable UPnP

Proceed as follows:

1

Browse to the

Thomson Gateway Web Interface

.

2

On the

Toolbox

menu, click

Game & Application Sharing

.

3

Under

Universal Plug and Play

:

²

Select the

Use UPnP

check box, to enable UPnP.

²

Clear the

Use UPnP

check box, to disable UPnP.

4

Click

Apply

.

Extended Security

If Extended Security is enable only limited UPnP operation between the host and the Thomson Gateway is

allowed. A local host is not allowed to connect/disconnect the Thomson Gateway Internet connection. You

can then only connect/disconnect the Internet connection on the

Thomson Gateway Web Interface

.

Enabling Extended Security

Proceed as follows:

1

Browse to the

Thomson Gateway Web Interface

.

2

On the

Toolbox

menu, click

Game & Application Sharing

.

3

Under

Universal Plug and Play

, select

Use Extended Security

.

4

Click

Apply

.

Page 57 / 88

E-DOC-CTC-20080118-0051 v2.0

51

4

Getting the Most Out of Your Thomson Gateway

4.3.4

Installing UPnP on Windows XP

Adding UPnP

If you are running Microsoft Windows XP, it is recommended to add the UPnP component to your system.

Proceed as follows:

1

In the

Start

menu, click

(Settings >) Control Panel

.

2

The

Control Pane

l window appears.

Click

Add or Remove Programs

.

3

The

Add or Remove Programs

window appears.

Click

Add/Remove Windows Components

.

4

The

Windows Components Wizard

appears:

In the

Components

list, select

Networking Services

and click

Details

5

The

Networking Services

window appears:

Select

Universal Plug and Play

or

UPnP User Interface

and click

OK

.

6

Click

Windows Components Wizard

.

7

At the end of the procedure the Wizard informs you that the installation was successful. Click

Finish

to

quit.

Page 58 / 88

E-DOC-CTC-20080118-0051 v2.0

52

4

Getting the Most Out of Your Thomson Gateway

Adding IGD Discovery and Control

Your Windows XP system is able to discover and control Internet Gateway Devices (IGD), like the Thomson

Gateway on your local network. Therefore, it is recommended to add the IGD Discovery and Control client to

your system.

Proceed as follows:

1

On the Windows taskbar, click

Start

.

2

Select

(Settings >) Control Panel

>

Add or Remove Programs

.

3

In the

Add or Remove Programs

window, click

Add/Remove Windows Components

.

4

The

Windows Components Wizard

appears:

Select

Networking Services

in the

Components

list and click

Details

.

5

The

Networking Services

window appears:

Select

Internet Gateway Device Discovery and Control Client

and click

OK

.

6

Click

Windows Components Wizard

.

7

At the end of the procedure, the Wizard informs you that the installation was successful. Click

Finish

to

quit.

Page 59 / 88

E-DOC-CTC-20080118-0051 v2.0

53

4

Getting the Most Out of Your Thomson Gateway

4.4

Assigning a service (HTTP, FTP,...) to a computer

Introduction

The Thomson Gateway allows you to use one internet connection for multiple computers. This means that all

your computers share one public IP address, as if only one computer is connected to the outside world.

Problem

When the Thomson Gateway receives an incoming message, the Thomson Gateway has to decide to which

computer he will have to send this message.

If the incoming message is a response to an outgoing message originating from one of your computers, the

Thomson Gateway sends the incoming message to this computer.

If your are running a server or an application that acts as a server (for example a HTTP server, internet game),

the initial message will come from the internet and the Thomson Gateway has to decide to which computer

he should forward the incoming message.

Solution

To avoid this problem you can:

±

Enable

UPnP

.

±

Assign a game or application to a local networking device

.

Internet

?

Page 60 / 88

E-DOC-CTC-20080118-0051 v2.0

54

4

Getting the Most Out of Your Thomson Gateway

UPnP

UPnP is a technology that enables seamless operation of a wide range of games and messaging applications.

Your computer will use UPnP to communicate to the Thomson Gateway which services are running on the

computer.

For more information on UPnP, see

“4.3 Universal Plug and Play” on page 46

.

Assign a game or application to a local networking device

If you assign a game or application to a local networking device, you will basically tell the Thomson Gateway

that if it receives requests for a specific game or application, it has to forward these messages to a specific

computer.

Proceed as follows to do so:

1

Browse to the

Thomson Gateway Web Interface

.

2

On the

Toolbox

menu, click

Game & Application Sharing

.

3

In the

Pick a task

list, click

Assign a game or application to a local network device

.

4

In the

Game or application

list, click the service you want to run on the computer. For example,

HTTP

Server (World Wide Web)

.

5

In the

Device

, list select the computer to which you want to assign the service. Your computer will be

listed with it’s computer name.

6

All incoming request for the selected service will now be directed to the selected device. The Thomson

Gateway will also configure the Thomson Gateway firewall to allow this service.

If the service is not available in the list, click

Create a new game or application

in the

Pick a task

list. For more information, click

Help

on the

Thomson Gateway Web Interface

.

Rate

Popular Thomson Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share