Thomson TCW770 Router Manual PDF (Setup & Configuration Guide)

Page 51 / 76 Scroll up to view Page 46 - 50

Chapter 2: WEB Configuration

44

Illustrations contained in this document are for representation only.



RADIUS Server/RADIUS Port/RADIUS Key: Please refer to the previous page.



Group Key Rotation Interval

: Key in the time for the WAP group key rotation interval. The unit is

second. With increasing rekey interval, user bandwidth requirement is reduced.



WPA/WPA2 Re-auth Interval

: When a wireless client has associated with the Wireless Gateway

for a period of time longer than the setting here, it would be disconnected and the authentication will

be executed again. The default value is

3600

, you may modify it.

Fig. 33

WPA-PSK/ WPA2-PSK

For the WPA-PSK/WPA2-PSK network Authentication, the settings that you can adjust including

WPA/WPA2 Encryption, WPA Pre-Shared Key, and Group key Rotation Interval.



WPA Pre-Shared Key:

Please type the key to be between 8 and 63 characters, or 64 hexadecimal

digits.

Only the devices with a matching key that you set here can join this network.



WPA/WPA2 Encryption & WPA Group Rekey Interval:

Please refer to the WPA/WPA2 part.

Fig. 34

Downloaded from

www.Manualslib.com

manuals search engine

Page 52 / 76

Chapter 2: WEB Configuration

Illustrations contained in this document are for representation only.

45

Automatic Security Configuration

Fig. 35

WiFi Protected Setup (WPS) is an easy and secure way of configuring and connecting your WiFi access point.

In your case, the TCW770 is the Access Point (AP), and Your PC (or Wifi Device) is called the STA. When

configuring your Wifi Network via WPS, Messages are exchanged between the STA and AP in order to configure

the Security Settings on both devices.



WPS Config:

It will help you to

Enable

or

Disable

the WPS feature. To enable you need to select

WPS

, to

disable you need to select

Disabled

.

Note:

After you

Enabled

the WPS you will get the options as show in Fig.35 and the WPS Config State box

will show its configuration status.



Device Name:

By using this you can change the factory default to a name of your choice which is up to 32

characters long as like

SSID

.



WPS Setup AP:

Here you do not need to change anything, just skip this step.



WPS Add Client:

T

here are two methods ―Push

-

Button‖ and ―PIN‖. Select the method

you want.

But, the default

selection will be ―

‖.

If you select ―Push

-

Button‖,

then the

WPS Add Client

option will appear as shown below.

Fig. 36

An

d then if you click ―

Add

‖ button then

WPS Setup AP

page will appear as shown in Fig.37

Downloaded from

www.Manualslib.com

manuals search engine

Page 53 / 76

Chapter 2: WEB Configuration

46

Illustrations contained in this document are for representation only.

Fig. 37

And

WPS Configure Status

will be ―In progress‖, after establishing the connection the

WPS Configure

Status

will be ―Success!‖

as shown below. After successful connection the client will get IP address from AP

and then internet will be accessible.

Fig. 38

If you select

WPS Method

to PIN then it will ask for PIN while configuring the WiFi AP by showing a text

box so, you need to enter PIN to establish

the connection. You can get the PIN from your connected Wi-Fi

client.

Fig. 39



PIN:

Use this option to set the PIN, enter 4-8 digits PIN of the device you wish to configure. After entering

the pin click ―Add‖ button,

then the

WPS Setup AP

page will appear as shown in Fig.38

Downloaded from

www.Manualslib.com

manuals search engine

Page 54 / 76

Chapter 2: WEB Configuration

Illustrations contained in this document are for representation only.

47

Fig. 40

And

WPS Configure Status

will be ―In progress‖, after establishing the connection the

WPS Configure

Status

will be ―Success!‖

as shown below. After successful connection the client will get IP address from AP

and then internet will be accessible.

Fig. 41

Downloaded from

www.Manualslib.com

manuals search engine

Page 55 / 76

Chapter 2: WEB Configuration

48

Illustrations contained in this document are for representation only.

3. Access Control

This page allows you to make access control to the AP (Access Point) or connected clients by offering the

MAC Addresses of the clients.

Fig. 42

Administration Web page Access:

It Allow or Deny access to Administration Web Page from PC

connected over WiFi.

Wireless Interface:

By default it will be having

two interfaces, ―Primary Network interface‖ and ―Guest

Network Interface‖. The ―Primary Network interface‖ will be available for all users. If

you want to access

the ―Guest Network Interface‖ then you need to contact cable operator.

MAC Restrict Mode:

Click

Disabled

to welcome all of the clients on the network; select

Allow

to

permit only the clients on the list to access the cable modem; or choose

Deny

to prevent the clients on the

list to access this device.

MAC Address:

Your Gateway identifies wireless PCs by their WiFi MAC Address. This address consists

of a string of 6 pairs of numbers 0-9 and letters A-F, such as 00 90 4B F0 FF 50. It is usually printed on

the WiFi card of the device (e.g. the PCMCIA card in a laptop). It can also be determined from a

Windows DOS prompt as explained below.

Enter the MAC addresses of the connected clients into the fields, and then click Apply to add them to the

list for access control.

Apply:

After proper configuration, click Apply to invoke the settings.

Connected Clients:

The information of currently connected clients will be displayed here.

Downloaded from

www.Manualslib.com

manuals search engine

Rate

Popular Thomson Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share