Page 11 / 110
Scroll up to view Page 6 - 10
3
E-DOC-CTC-20051017-0147 v2.0
Chapter 1
Getting to know your SpeedTouch™
1
Getting to know your SpeedTouch™
Introduction
With the SpeedTouch™585
(v6)
(i) Wireless Residential ADSL Gateway you can build a
secure home or small office network, seamlessly connecting wired and wireless
devices and surf the Internet at high speed, all combined in one device.
Installation
For more information on how to set up, install and wire your SpeedTouch™ and set
up Internet connection, refer to the Installation and Setup Guide.
Configuration
This User’s Guide will help you configuring your SpeedTouch™.
Before you begin
Before connecting the SpeedTouch™, please read the SpeedTouch™ Quick
Installation Guide and the Safety Instructions and Regulatory Notices.
Page 12 / 110
4
E-DOC-CTC-20051017-0147 v2.0
Chapter 1
Getting to know your SpeedTouch™
1.1
SpeedTouch™ LED Behaviour
Front panel LEDs
The SpeedTouch™ is equipped with a number of LEDs on its front panel, indicating
the state of the device during normal operation.
The following table shows the meaning of the different LEDs.
Indicator
Description
Name
Colour
State
Power
Green
Solid on
Power on, normal operation
Red
Solid on
Power on, self-test failed, indicating
device malfunction
Orange
Solid on
Bootloader active
Off
Power off
Ethernet
Green
Blinking
Ethernet activity
Solid on
Ethernet connection, no activity
Off
No Ethernet connection
WLAN
Green
Blinking
Wireless activity, WPA encryption
Solid on
No wireless activity, WPA encryption
Amber
Blinking
Wireless activity, WEP encryption
Solid on
No wireless activity, WEP encryption
Red
Blinking
Wireless activity, no security
Solid on
No wireless activity, no security
Red/
green
Toggling
Wireless client registration phase
Off
WLAN disabled
Page 13 / 110
5
E-DOC-CTC-20051017-0147 v2.0
Chapter 1
Getting to know your SpeedTouch™
Ethernet LEDs
A LED may be provided per Ethernet port to indicate link integrity (or activity).
Depending on the SpeedTouch™ product you are using, a second LED (A) may be
provided to indicate the 10/100Base-T selection:
DSL
Green
Blinking
Pending DSL line synchronisation
Solid on
DSL line synchronised
Off
No DSL line
Internet
Green
Blinking
Internet activity
Solid on
Internet connectivity, no activity
Red
Solid on
Internet connection setup failed
Off
No Internet connection
Indicator
Description
Name
Colour
State
Indicator
Description
Name
LED Status
A
(Optional)
Integrity
(Activity)
Off
No connection on this port
Solid on
Ethernet link up
Blinking
Data is flowing from/to this port
B
10/100Base-T
Off
10Base-T Ethernet connection
Solid on
100Base-T Ethernet connection
A
B
Page 14 / 110
6
E-DOC-CTC-20051017-0147 v2.0
Chapter 1
Getting to know your SpeedTouch™
1.2
Accessing your SpeedTouch™
Access methods
Your SpeedTouch™ is accessible in one of the following ways:
Access Method
Can be used to
Web browser
Configure your SpeedTouch™ via HTTP or
HTTPS.
For more information, see
“1.2.1 Access via
the Web Interface” on page 7
.
Command Line Interface (CLI)
Fine-tune your SpeedTouch™ configuration.
For more information, see
“1.2.2 Access via
CLI” on page 8
.
File Transfer Protocol (FTP)
Back up and restore data on your
SpeedTouch™.
For more information, see
“1.2.3 Access via
FTP” on page 10
.
Remote Assistance
Allow a remote user to help you configuring
your SpeedTouch™.
For more information, see
“1.2.4 Remote
Assistance” on page 13
.
Page 15 / 110
7
E-DOC-CTC-20051017-0147 v2.0
Chapter 1
Getting to know your SpeedTouch™
1.2.1
Access via the Web Interface
To access the
SpeedTouch™ via the
Web interface
Proceed as follows:
1
Open a Web browser.
2
In the address bar, type your SpeedTouch™’s IP address or DNS host name
(
h
ttp://speedtouch.lan
or
192.168.1.254
by default)
The SpeedTouch™
Home
page appears, from where you can navigate to all
the configurable aspects of the SpeedTouch™.
For more information on the Web pages, see
“4 SpeedTouch™ Web Interface” on
page 35
.
You can access the pages via HTTP or HTTPS.
For remote assistance the secure version HTTPS is used in
combination with certificates. Simply provide your ISP with the link as
shown, user name and password before he can log on to the pages.
For more information, see
“1.2.4 Remote Assistance” on page 13
.
19216811.live