Page 6 / 110 Scroll up to view Page 1 - 5
TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router
Chapter 1: Introduction
5
Rich Packet Filtering
Not only filters the packet based on IP address, but also based on Port numbers. It will filter
packets from and to the Internet, and also provides a higher level of security control.
Dynamic Host Configuration Protocol (DHCP) client and server
In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP)
automatically. In the LAN site, the DHCP server can allocate a range of client IP addresses and
distribute them including IP address, subnet mask as well as DNS IP address to local computers. It
provides an easy way to manage the local IP network.
Static and RIP1/2 Routing
It has routing capability and supports easy static routing table or RIP1/2 routing protocol.
Simple Network Management Protocol (SNMP)
It is an easy way to remotely manage the router via SNMP.
Web based GUI
It supports web based GUI for configuration and management. It is user-friendly and comes with
on-line help. It also supports remote management capability for remote users to configure and
manage this product.
Firmware Upgradeable
Device can be upgraded to the latest firmware through the WEB based GUI.
Rich management interfaces
It supports flexible management interfaces with local console port, LAN port, and WAN port. Users
can use terminal applications through the console port to configure and manage the device, or
Telnet, WEB GUI, and SNMP through LAN or WAN ports to configure and manage the device.
Page 7 / 110
TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router
Chapter 1: Introduction
6
TW-EA510v4 ADSL Router Application
Figure 1.1 Application Diagram of
TW-EA510v4
Thank you for your purchase, and welcome to the world of broadband Internet
Page 8 / 110
TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router
Chapter 2: Installing the router
7
Chapter 2: Installing the Router
Important note for using this router
Package Contents
802.11g ADSL2+ Firewall Router
RJ-11 ADSL/telephone Cable
Ethernet (CAT-5 LAN) Cable
RJ-45 to RS-232 Console Kit
AC-DC power adapter (12VDC, 1A)
A detachable antenna
Manual
±
Do not use this router in high humidity or high temperatures.
±
Do not use the same power source for this router as other
equipment.
±
Do not open or repair the case yourself.
If this router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
±
Avoid using this product and all accessories outdoors.
Warning
±
Place this router on a stable surface.
±
Only use the power adapter that comes with the package.
Using
a different voltage rating power adaptor may damage this router.
Attention
Page 9 / 110
TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router
Chapter 2: Installing the router
8
The Front LEDs
LED
Meaning
1
Internet
Lit green when
IP connected
.
Flashes green when IP connected and IP traffic is passing thru the
device.
Lit red when device attempted to become IP connected and failed.
2
DSL
Lit green when successfully connected to an ADSL DSLAM
(“linesync”).
3
Ethernet
Port
1X — 4X
(RJ-45 connector)
Lit when the LAN link is connected to an Ethernet device.
Green for 100Mbps; Orange for 10Mbps.
Blinking when data is Transmitted / Received.
4
Wireless
Lit green when the wireless connection is established.
Flashes when sending/receiving data.
Flashes at 1Hz when WPS is active.
5
Mail
Lit and flashed periodically when there is email in the Inbox.
6
Power
Lit green when power on.
Lit red when POST(Power On Self Test) failure (not bootable) or
device malfunction.
Page 10 / 110
TW-EA510 version 4 ADSL2+, WLAN 802.11g, VPN, Firewall Router
Chapter 2: Installing the router
9
The Ethernet Port # 4 can be used as a console port. You need a special
console tool that already includes in the package to connect with LAN port 4
and PC’s RS-232 port (9-pin serial port).
The Rear Ports
Port
Meaning
1
Power Switch
Power ON/OFF switch
2
Power
Connect the supplied power adapter to this jack.
3
RESET
To be sure the device is being turned on
±
press RESET button for:
1-3 seconds
: quick reset the device.
6 seconds above, and power off, power on the device
: restore to
factory default settings.
(Cannot login to the router or forgot your
Username/Password.
Press the button for more than 6 seconds).
Caution
: After pressing the RESET button for more than 6 seconds, to be
sure you power cycle the device again.
4
Ethernet Port
1X — 4X
(RJ-45 connector)
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four
LAN ports when connecting to a PC or an office/home network of
10Mbps or 100Mbps.
Caution
: Port 4 can be either a LAN or Console port at a time but not both.
5
WPS Push Button
WPS (Wi-Fi Protected Setup) is designed to ease set up of security-
enabled Wi-Fi networks in the home and small office environment.
Note: This feature is suppted later by software update. Press WPS Push
Button to activate WPS feature.
6
DSL
Connect the supplied RJ-11 (“telephone”) cable to this port when
connecting to the ADSL/telephone network.
2
5
6
1
3
4

Rate

4 / 5 based on 1 vote.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top