Telewell TW-EA510v3-b Router Manual PDF (Setup & Configuration Guide)

Page 16 / 95 Scroll up to view Page 11 - 15

14

Configuring PC in Windows 98/Me

1.

Go to

Start / Settings / Control Panel

.

In the Control Panel, double-click on

Network

and choose the

Configuration

tab.

2.

Select

TCP/IP ->NE2000 Compatible

,

or the name of your Network Interface

Card (NIC) in your PC.

3.

Select the

Obtain an IP address

automatically

radio button.

4.

Then select the

DNS Configuration

tab.

5

.Select the

Disable DNS

radio button

and click

OK

to finish the configuration.

Page 17 / 95

15

Configuring PC in Windows NT4.0

1.

Go to

Start / Settings / Control Panel

.

In the Control Panel, double-click on

Network

and choose the

Protocols

tab.

2.

Select

TCP/IP Protocol

and click

Properties

.

3.

Select the

Obtain an IP address from a

DHCP server

radio button and click

OK

.

Page 18 / 95

16

3.2 Factory Default Settings

Before configuring the router, you need to know the following default settings.

Web Interface:

Username: admin

Password: admin

LAN Device IP Settings:

IP Address: 192.168.0.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

RFC 1483 LLC Bridge

Auto support for VPI=0,14 and VCI=24,33,50,100 if auto-scan fails!

During the 1

st

connection IP – traffic may take 2-4 minutes after boot.

Device will auto-scan correct parameters for ISP line on this period.

NAT enabled

DHCP Server:

DHCP server is enabled.

Start IP Address: 192.168.0.100

IP pool counts: 100

3.3 Username and Password

The default username and password are “

admin

” and “

admin

” respectively.

To reset the router or to restore it to factory default settings press the

Reset button using the end of paper clip or other small pointed object.

1. To perform Failure recovery for a dead router:

Simply hold the Reset button when powering on the router and

download an application if necessary.

2. To perform recovery in case of a misplaced Password:

Hold the Reset button until the LEDs all turn Off, turn On and then turn

Off. The router performs configuration factory reset and the router

reboots. You can then access the router from the web GUI.

Attention

Page 19 / 95

17

3.4 LAN and WAN Port Addresses

The parameters of LAN and WAN ports are preset at the factory.

The default values are

shown below.

LAN Port

WAN Port

IP address

192.168.0.254

Subnet Mask

255.255.255.0

DHCP server function

Enabled

IP addresses for

distribution to PCs

100 IP addresses continuing from

192.168.0.100 through

192.168.0.199

Bridge is automatic

setting in WAN port.

3.4 Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider)

what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE

VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password, Service Name, and Domain Name System (DNS)

IP address (it can be automatically assigned by your ISP when

you connect or be set manually).

PPPoA

VPI/VCI, VC-based/LLC-based multiplexing, Username,

Password, and Domain Name System (DNS) IP address (it

can be automatically assigned by your ISP when you connect

or be set manually).

RFC1483 Bridged

VPI/VCI, VC-based/LLC-based multiplexing to use Bridged

Mode.

RFC1483 Routed

VPI/VCI, VC-based/LLC-based multiplexing, IP address,

Subnet mask, Gateway address, and Domain Name System

(DNS) IP address (it is fixed IP address).

Page 20 / 95

18

3.5 Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is

192.168.0.254

, and click “

Go

”, a user name and password window prompt appears.

The

default username and password are “admin” and “admin”.

Congratulations! You have successfully logged on to your 802.11g ADSL2+ Router!

Rate

Popular Telewell Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share