Telewell TW-EA510v3 Router Manual PDF (Setup & Configuration Guide)

Page 11 / 95 Scroll up to view Page 6 - 10

9

Before powered on the router to enter the recovery process. please

configure the IP address of the PC as 192.168.0.1 and process step by

step.

1. Power the router off.

2. Hold the " Emergency/Failure Recovery Button”.

3. Power on the router. Then Router's IP will reset to Default (Say

192.168.0.254)

4. Download the firmware.

The detail instruction in Emergency/Failure Recovery Button

1.

Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash):

Hold the

Emergency/Failure Recovery Button

on the back of the modem in. Keep this

button held in and turn on the modem. Once the lights on the modem have stopped

flashing, release the

Emergency/Failure Recovery Button.

The modem's

emergency-reflash web interface will then be accessible via

http://192.168.0.254/

where

you can upload a firmware image to restore the modem to a functional state. Please note

that the modem will only respond via its web interface at this address, and will not

respond to ping requests from your PC or to telnet connections.

2. Recovery procedures for a lost web interface password:

After turning the router on press the

Emergency/Failure Recovery Button

on the back of

the modem, and hold the button in until all lights on the modem flash and it reboots with

factory default settings. The login will be reset to

admin

and the password will be reset to

admin

, and the modem will be accessible via its default IP address at

http://192.168.0.254/

Page 12 / 95

10

2.5 Cabling

One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that

all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that

the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper

cables.

Ensure that all other devices connected to the same telephone line as your router (e.g.

telephones, fax machines, analog modems) have a line filter connected between them and

the wall socket (unless you are using a Central Splitter or Central Filter installed by a

qualified and licensed electrician), and ensure that all line filters are correctly installed and

the right way around. Missing line filters or line filters installed the wrong way around can

cause problems with your ADSL connection, including frequent disconnections.

Page 13 / 95

11

Chapter 3

Installation

You can configure the router through the convenient and user-friendly interface of a web

browser. Most popular operating systems such as Linux, MAC, and Windows

98/NT/2000/XP/Me include a web browser as a standard application.

3.1 Before Configuration

PCs must have a properly installed Ethernet interface and connect to the router directly or

through an external repeater hub. In addition, PCs must have TCP/IP installed and

configured to obtain an IP address through a DHCP server or a fixed IP address that must be

in the same subnet as the router. The default IP address of the router is

192.168.0.254

and

the subnet mask is

255.255.255.0

(i.e. any attached PC must be in the same subnet, and

have an IP address in the range of 192.168.0.1 to 192.168.0.253). The easiest way is to

configure the PC to obtain an IP address automatically from the router using DHCP. If you

encounter any problems accessing the router’s web interface you are advised to

uninstall

any kind of software firewall on your PCs, as they can cause problems accessing the

192.168.0.254 IP address of the router.

Please follow the steps below for installation on your PC’s network environment. First of all,

check your PC’s network components. The TCP/IP protocol stack and Ethernet network

adapter must be installed. If not, please refer to your Windows-related or other operating

system manuals.

Page 14 / 95

12

Configuring a PC in Windows XP

1.

Go to

Start / Control Panel (in Classic

View)

. In the Control Panel, double-click

on

Network Connections

2.

Double-click

Local Area Connection

.

3.

In the

Local Area Connection Status

window, click

Properties

.

4.

Select

Internet Protocol (TCP/IP)

and

click

Properties

.

5.

Select the

Obtain an IP address

automatically

and

the

Obtain DNS

server address automatically

radio

buttons.

6.

Click

OK

to finish the configuration.

Page 15 / 95

13

Configuring a PC in Windows 2000

1.

Go to

Start / Settings / Control Panel

.

In the Control Panel, double-click on

Network

and Dial-up Connections

.

2.

Double-click

Local Area Connection

.

3.

In the

Local Area Connection Status

window click

Properties

.

4.

Select

Internet Protocol (TCP/IP)

and

click

Properties

.

5.

Select the

Obtain an IP address

automatically

and

the

Obtain DNS

server address automatically

radio

buttons.

6.

Click

OK

to finish the configuration.

Rate

Popular Telewell Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share