Soniq CWR150NS Router Manual PDF (Setup & Configuration Guide)

Page 46 / 90 Scroll up to view Page 41 - 45

- 45 -

Field

Description

to

WEP

. Click it, the

Wireless WEP Key Setup

page appears.

WPA Authentication

Mode

°

Select

Personal (Pre-Shared Key)

, enter the

pre-shared key in the

Pre-Shared Key

field.

°

Select

Enterprise (RADIUS)

, enter the port,

IP address, and password of the Radius server.

You need to enter the username and password

provided by the Radius server when the wireless

client connects the modem.

If the encrypton is set to

WEP

, the modem uses

802.1 X authentication, which is Radius

authentication.

Click

Set WEP Key

, and the following page appears.

The following describes the parameters of this page:

Field

Description

Key Length

Choose the WEP key length. You can Choose

64-bit

or

128-bit

.

Page 47 / 90

- 46 -

Field

Description

Key Format

°

If you choose

64-bit

, you can choose ASCII (5

characters) or Hex (10 characters).

°

If you choose

128-bit

, you can choose ASCII

(13 characters) or Hex (26 characters).

Default Tx Key

Choose the index of WEP Key. You can choose

Key

1

,

Key 2

,

Key 3

, or

Key 4

.

Encryption Key 1

to 4

The Encryption keys are used to encrypt the data.

Both the modem and wireless stations must use the

same encryption key for data transmission.

°

If you choose

64-bit

and

ASCII (5 characters)

,

enter any 5 ASCII characters.

°

If you choose

64-bit

and

Hex (10 characters)

,

enter any 10 hexadecimal characters.

°

If

you

choose

128-bit

and

ASCII

(13

characters)

, enter any 13 ASCII characters.

°

If you choose

128-bit

and

Hex (26 characters)

,

enter any 26 hexadecimal characters.

Apply Changes

Click it to apply the settings temporarily. If you want

to save the settings of this page permanently, click

Save

in the lower left corner.

3.4.3.3 Access Control

Choose

WLAN

>

Access Control

and the following page appears. In this page,

you can configure the access control of the wireless clients.

Page 48 / 90

- 47 -

Choose

Allow Listed

as the access control mode to enable white list function.

Only the devices whose MAC addresses are listed in the

Current Access Control

List

can access the modem.

Choose

Deny Listed

as the access control mode to to enable black list function.

The devices whose MAC addresses are listed in the

Current Access Control List

are denied to access the modem.

3.4.3.4 Advanced Settings

Choose

Wireless

>

Advanced

Settings

and the following page appears. In this

page, you can configure the wireless advanced parameters. It is recommended to

use the default parameters.

Page 49 / 90

- 48 -

Note:

The parameters in the

Advanced Settings

are modified by the professional

personnel, it is recommended to keep the default values.

The following table describes the parameters of this page:

Field

Description

Authentication

Select the modem operating in the open system or

Page 50 / 90

- 49 -

Field

Description

encryption authentication. You can choose

Open

System,

Shared Key

, or

Auto

.

°

In the open system, the wireless client can

directly connect to the device

°

In the encryption authentication, the wireless

client connects to the modem through the shared

key.

Data Rate

Choose the transmission rate of the wireless data.

You can choose

Auto

,

1 M

,

2 M

,

5.5 M

,

11 M

,

6 M

,

9 M

,

12 M

,

18 M

,

24 M

,

36 M

,

48

M

,

54M,

MSC0-MSC15.

PreambleType

°

Long Preamble

: It means this card always

use long preamble.

°

Short Preamble

: It means this card can

support short preamble capability.

Broadcast SSID

Select whether the modem broadcasts SSID or not.

You can select

Enable

or

Disable

.

°

Select

Enable

, the wireless client searches the

modem through broadcasting SSID.

°

Select

Disable

to hide SSID, the wireless

clients can not find the SSID.

Relay Blocking

Wireless isolation. Select

Enable

, the wireless

clients that are connected to the modem can not

intercommunication.

Ethernet to

Wireless Blocking

Whether the wireless network can communicate

with the Ethernet network or not.

Wifi Multicast to

Unicast

Enable it to using unicast to transmit multicast

packet

Aggregation

It is applied when the destination end of all MPDU

are for one STA.

Short GI

It is not recommended to enable GI in obvious

environment of Multi-path effect.

Rate

Popular Soniq Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share