1. Home
    2. /
  2. Manuals
    3. /
  3. SmartRG
    4. /
  4. SR500N
    5. /
  5. 6
Page 26 / 59 Scroll up to view Page 21 - 25
SmartRG™ Resi
dential Gateways
P a g e
| 26
C o n f i d e n t i a l
S m a r t R G © 2 0 1 2
not included in the DHCP server pool on the primary SmartRG gateway.
IMPORT
ANT
At this point your web browser session will terminate as the LAN IP addres
from 192.168.1.1 to 192.168.1.x. Reconnect your web browser to the rem
referencing the new LAN IP address.
To configure the WIRELESS interfaces
…
5.
On the primary SmartRG gateway: configure the WIRELESS interface following
the instructions in the “
Use Case: Setting Up Wireless
” section.
Do NOT select
“Auto” for the Channel value.
6.
On the remote SmartRG gateway(s): configure the WIRELESS interface
following the instructions in the “
Use Case: Setting Up Wireless
” section.
Select
the same SSID, Security settings and Channel configured on the primary
gateway.
7.
On the primary
and
remote SmartRG gateways:
1.
select Wireless -> Wireless Bridge and s
et “AP Mode” to Access Point
2.
set “Bridge Restrict” to Enabled(SCAN)
3.
click Apply/Save and wait for the page to refresh
4.
select the partner gateway (which has the same SSID as the primary
gateway) by checking the box next to the SSID.
5.
Click Apply/Save
IMPORT
ANT
When more than two gateways are configured for WDS operation, the rem
MUST NOT be partnered together to avoid creating an Ethernet loop.
Use Case: Creating IPTV Service Configurations
”
you MUST enable IGMP.
Page 27 / 59
Configuring Your SmartRG™
- Common Use Cases
S m a r t R G © 2 0 1 2
C o n f i d e n t i a l
P
a
g
e
| 27
Figure 17 WAN NAT, Firewall and IGMP Settings
8.
Select the WAN interface to be used by this WAN service. Click Next.
9.
Select “Obtain DNS
info from a WAN interface” and select the desired WAN interface from
the drop down list (a single WAN interface is common
unless
you are creating bridged IPTV
configurations)
–
or-
select “Use the following Static DNS IP address” and enter the IP
addresses
of your network’s primary and secondary DNS servers. Click
Next.
10.
Review the WAN service summary. If you are satisfied click Apply/Save.
Page 28 / 59
SmartRG™ Resi
dential Gateways
P a g e
| 28
C o n f i d e n t i a l
S m a r t R G © 2 0 1 2
Use Case: Provisioning Your SmartRG for Remote ACS Management
NOTE
This step is not required for production SmartRG gateways. SmartRG maintains an
“Activation Server” that associates MAC addresses with service providers’ ACS
management URLs. After the SmartRG has established its WAN connection (using the
Connect-and-Surf algorithm) it connects to the SmartRG Activation Server and reports its
MAC. The Activation Server changes the ACS management URL to point to the service
provider’s ACS
.
To manually provision your SmartRG for management by a TR-069 enabled Automated
Configuration Server:
1.
Select
Management -> Management Server -> TR-069 Client.
Figure 18 TR-069 Management Settings
2.
Enter the following
parameter values:
Enable “Informs”
Set the “Inform Interval” to
7200 seconds
Set the “ACS URL”
(e.g.
)
Leave the “ACS User Name” and “ACS Password” blank
Enable “Connection Request Authentication”
Set the “Connection Request User Name and Password” to admin/admin
3.
Click Apply/Save.
NOTE
Configure less and deploy more. Manage subscriber services and your entire gateway
fleet with the ClearVision® management system. Contact SmartRG to start your trial
today. See us at
www.smartrg.com
.
Page 29 / 59
Configuring Your SmartRG™
- Common Use Cases
S m a r t R G © 2 0 1 2
C o n f i d e n t i a l
P
a
g
e
| 29
Use Case: Setting Up the LAN
To configure the SmartRG’s LAN interf
ace:
1.
Select
Advanced Setup -> LAN
Figure 19 LAN Settings
2.
Leave the “GroupName” as Default
.
3.
Set the LAN interface’s “IP Address” and “Subnet Mask” –
Default values are:
192.168.1.1/255.255.255.0.
4.
IMPORTANT
–
If you intend to support IPTV (either bridged or routed), you MUST select
“Enable IGMP Snooping.”
Select “Blocking Mode.”
5.
Select “Enable DHCP Server” and set the DHCP address pool’s start and end IP addresses.
6.
Set the DHCP “Leased Time” in hours
.
7.
If you would like to create static DHCP leases for specific LAN hosts,
click Add Entries.
Page 30 / 59
SmartRG™ Resi
dential Gateways
P a g e
| 30
C o n f i d e n t i a l
S m a r t R G © 2 0 1 2
Figure 20 Adding DHCP Static IP Leases
8.
Enter the LAN host’s “MAC Address” and the desired “IP Address.”
9.
Click Apply/Save and repeat steps 7 and 8 for all static IP LAN hosts.

Rate

4 / 5 based on 1 vote.

Popular SmartRG Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top