Sitecom WL-322 Router Manual PDF (Setup & Configuration Guide)

Page 46 / 57 Scroll up to view Page 41 - 45

46

QoS

QoS can let you classify Internet application traffic by source/destination IP

address and port number. You can assign priority for each type of application

and reserve bandwidth for it. The packets of applications with higher priority

will always go first. Lower priority applications will get bandwidth after higher

priority applications get enough bandwidth. This can let you have a better

experience in using critical real time services like Internet phone, video

conference …etc. All the applications not specified by you are classified as rule

name “Others”. The rule with a smaller priority number has a higher priority;

the rule with a larger priority number has a lower priority. You can adjust the

priority of the rules by moving them up or down.

Enable/Disable

QoS

You can check “Enable QoS” to enable QoS

functionality for the WAN port.

Traffic mapping

Click “Add traffic class” then enter a form of the QoS rule.

Click “Apply” after filling out the form the rule will be added into the table.

Page 47 / 57

47

Edit a QoS rule

Select the rule you want to edit and click “Edit”, then enter

the detail form of the QoS rule. Click “

Apply

” after editing the form and the

rule will be saved.

Adjust QoS rule

priority You can select the rule and click “Move Up” to make

its priority higher. You also can select the rule and click “Move Down” to make

its priority lower.

Page 48 / 57

48

Routing

These screens define routing related parameters, including static routes and

RIP (Routing Information Protocol) parameters.

Routing Table

Flags Indicates the route status:

C = Direct connection on the same subnet.

S = Static route.

R = RIP (Routing Information Protocol) assigned route.

I = ICMP (Internet Control Message Protocol) Redirect route.

Static Route

Click

Add

to add a new static route to the list, or check the box of

an already entered route and click

Modify

. Clicking

Delete

will remove an

entry from the list.

RIP

RIP mode Globally enables or disables RIP.

Auto summary If Auto summary is disabled, then RIP packets will

include sub-network information from all sub-networks connected to the router.

If enabled, this sub-network information will be summarized to one piece of

information covering all sub-networks.

Table of current Interface RIP parameter Interface The WAN interface to be

configured. Operation Mode Disable: RIP disabled on this interface.

Enable: RIP enabled on this interface. Silent: Listens for route broadcasts and

updates its route table. It does not participate in sending route

broadcasts. Version Sets the RIP (Routing Information Protocol)

version to use on this interface.

Page 49 / 57

49

Snmp

Use the SNMP configuration screen to display and modify parameters for

the Simple Network Management Protocol (SNMP).

SNMP operation mode

to select the SNMP modes for this device.

Community

A computer attached to the network, called a Network Management

Station (NMS), can be used to access this information. Access rights to the agent

are controlled by community strings. To communicate with the Router, the NMS

must first submit a valid community string for authentication.

Note:

Up to five community names may be entered.

Page 50 / 57

50

Trap

Specify the IP address of the NMS to notify when a significant event is

detected by the agent. When a trap condition occurs, the SNMP agent sends an

SNMP trap message to any NMS specified as a trap receiver.

IP Address Traps are sent to this address when errors or specific events

occur on the network. Community A community string (password) specified for

trap management. Enter a word, something other than public or

private, to prevent unauthorized individuals from accessing

information on your system. Version Sets the trap status to disabled, or enabled

with V1 or V2c. The v2c protocol was proposed in late 1995 and includes

enhancements to v1 that are universally accepted. These include a get-bulk

command to reduce network management traffic when retrieving a sequence of

MIB variables, and a more elaborate set of error codes for improved reporting to

a Network Management Station.

Rate

Popular Sitecom Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share