Page 16 / 66 Scroll up to view Page 11 - 15
14
Configuring PC in Windows NT4.0
1.
Go to
Start / Settings / Control Panel
.
In the Control Panel, double-click on
Network
and choose the
Protocols
tab.
2.
Select
TCP/IP Protocol
and click
Properties
.
3.
Select the
Obtain an IP address from a
DHCP server
radio button and click
OK
.
Page 17 / 66
15
3.2 Factory Default Settings
Before configuring your, you need to know the following default settings.
Web Interface:
Username: admin
Password: admin
LAN Device IP Settings:
IP Address: 192.168.1.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site:
PPPoE
DHCP server:
DHCP server is enabled.
Start IP Address: 192.168.1.100
IP pool counts: 100
3.2.1 Username and Password
The default username and password are “
admin
” and “
admin
” respectively.
Attention
If you ever forget the password to log in, you may press the RESET
button up to 6 seconds to restore the factory default settings.
Attention
Page 18 / 66
16
3.3 LAN and WAN Port Addresses
The parameters of LAN and WAN ports are pre-set in the factory.
The default values are
shown below.
LAN Port
WAN Port
IP address
192.168.1.254
Subnet Mask
255.255.255.0
DHCP server function
Enabled
IP addresses for
distribution to PCs
100 IP addresses continuing from
192.168.1.100 through
192.168.1.199
The PPPoE function is
enabled
to
automatically get the
WAN port
configuration from the
ISP, but you have to
set the username and
password first.
3.4 Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider)
what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password,
Service Name, and Domain Name System (DNS) IP address (it can
be automatically assigned by your ISP when you connect or be set
manually).
PPPoA
VPI/VCI, VC-based/LLC-based multiplexing, Username, Password,
and Domain Name System (DNS) IP address (it can be
automatically assigned by your ISP when you connect or be set
manually).
RFC1483 Bridged
VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.
RFC1483 Routed
VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet
mask, Gateway address, and Domain Name System (DNS) IP
address (it is fixed IP address).
Page 19 / 66
17
3.5 Configuring with your Web Browser
Open your web browser, enter the IP address of your router, which by default is
192.168.1.254
, and click “
Go
”, a user name and password window prompt will appear.
The
default username and password are “admin” and “admin”.
Congratulation! You are now successfully logon to the H6300G ADSL2+ Router!
Page 20 / 66
18
Chapter 4
Configuration
At the configuration homepage, the left navigation pane where bookmarks are provided links
you directly to the desired setup page, including:
Quick Start
(wizard setup)
Interface Setup
(Internet, LAN, Wireless)
Advanced Setup
(Firewall, Routing, NAT, ADSL)
Access Management
(ACL, Filter, SNMP, UPnP, DDNS)
Maintenance
(Administration, Time Zone, Firmware, SysRestart, Diagnositics)
Status
(Device Info, System Log, Statistics)
Help
Please see the relevant sections of this manual for detailed instructions on how to configure
your Prolink router.

Rate

4.5 / 5 based on 2 votes.

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top