1. Home
    2. /
  2. Manuals
    3. /
  3. Prolink
    4. /
  4. H5200
    5. /
  5. 8
Page 36 / 59 Scroll up to view Page 31 - 35
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 36 of 59
Fields settings on the first block:
Field
Description
RIP
Enable/disable RIP feature.
Function buttons for the second setting block in this page:
Apply Changes
Click to save the setting of this block to the system configuration
Fields settings on the second block:
Field
Description
Interface
The name of the interface on which, you want to enable RIP.
Receive Mode
Indicate the RIP version in which, information must be passed to the
modem/router in order for it to be accepted into its routing table.
Send Mode
Indicate the RIP version this interface will use when it sends its route
information to other devices.
Page 37 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 37 of 59
Function buttons for the second setting block in this page:
Add
Add a RIP entry and the new RIP entry will be display in the table.
Delete Selected Entry
Delete a selected RIP entry. The RIP entry can be selected on the
Select
column of the
RIP
Config Table.
Delete All
Delete all entries in
RIP Config Table
.
Page 38 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 38 of 59
9 Advance Configuration
9.1
BRIDGING
You can enable/disable Spanning Tree Protocol and set MAC address aging time in this
page.
Fields in this page:
Field
Description
Ageing Time
Set the Ethernet address ageing time, in seconds. After [Ageing Time]
seconds of not having seen a frame coming from a certain address, the bridge
will time out (delete) that address from Forwarding Database (fdb).
802.1d Spanning
Tree
Enable/disable the spanning tree protocol
Function buttons in this page:
Apply Changes
Save this bridge configuration. New configuration will take effect after saving into flash
Page 39 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 39 of 59
memory and rebooting the system
(See section “Admin” for details).
Show MACs
List MAC addresses in forwarding table.
9.2
ROUTING
The Routing page enables you to define specific route for your Internet and network data.
Most users do not need to define routes. On a typical home or small office LAN, the
existing routes that set up the default gateways for your LAN hosts and for the
modem/router, provide the most appropriate path for all your Internet traffic.
−
On your LAN hosts, a default gateway directs all Internet traffic to the LAN port(s)
on the modem/router. Your LAN hosts know their default gateway either because
you assigned it to them when you modified your TCP/IP properties, or because you
configured them to receive the information dynamically from a server whenever
they access the Internet.
−
On the modem/router itself, a default gateway is defined to direct all outbound
Internet traffic to a route at your ISP. The default gateway is assigned either
automatically by your ISP whenever the modem negotiates an Internet access, or
manually by user to setup through configuration.
You may need to define routes if your home setup includes two or more networks or
subnets, if you connect to two or more ISP services, or if you connect to a remote
corporate LAN.
Page 40 / 59
PROLiNK Hurricane 5200C/5201
ADSL2+ Modem / Router
User Manual
Page 40 of 59
Fields in this page:
Field
Description
Enable
Check to enable the selected route or route to be added.
Destination
The network IP address of the subnet. The destination can be specified as the
IP address of a subnet or a specific host in the subnet. It can also be specified
as all zeros to indicate that this route should be used for all destinations for
which no other route is defined
(this is the route that creates the default
gateway)
.
Subnet Mask
The network mask of the destination subnet. The default gateway uses a
mask of 0.0.0.0.
Next Hop
The IP address of the next hop through which traffic will flow towards the
destination subnet.
Metric
Defines the number of hops between network nodes that data packets travel.
The default value is 0, which means that the subnet is directly one hop away
on the local LAN network.
Interface
The WAN interface to which a static routing subnet is to be applied.

Rate

4.7 / 5 based on 3 votes.

Popular Prolink Models

Famous Router IPs
Famous Router Companies
Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top