Planet ADN-4101 Router Manual PDF (Setup & Configuration Guide)

Page 41 / 73 Scroll up to view Page 36 - 40

802.11n Wireless ADSL2/2+ Router

ADN-4101

Set the encryption mode to

WEP

and click

Set WEP Key

and the following page appears.

3.4.3.3 Access Control List

Choose

WLAN

>

Access Control List

and the following page appears. On this page, you can configure the access

control of the wireless clients.

Choose

Allow Listed

as the access control mode to enable white list function. Only the devices whose MAC

addresses are listed in the

Current Access Control List

can access the modem.

Choose

Deny Listed

as the access control mode to enable black list function. The devices whose MAC addresses

are listed in the

Current Access Control List

are denied to access the modem.

36

Page 42 / 73

802.11n Wireless ADSL2/2+ Router

ADN-4101

3.4.3.4 MBSSID

Choose

Wireless

>

MBSSID

and the following page appears. On this page, you can configure the multi-SSID of the

wireless clients.

It supports four virtual access points (VAPs). It is a unique name to identify the modem in the wireless LAN. Wireless

stations associating to the modem must have the same name. Enter a descriptive name that is used when the

wireless client connecting to the modem.

3.4.3.5 Advanced

Choose

WLAN

>

Advanced

and the following page appears. On this page, you can configure the wireless advanced

parameters. It is recommended to use the default parameters.

The parameters in the

Advanced

are modified by the professional personnel. It is

recommended to keep the default values

37

Page 43 / 73

802.11n Wireless ADSL2/2+ Router

ADN-4101

The following table describes the parameters on this page:

Field

Description

Authentication

Select the modem operating in the open system or encryption authentication.

You can choose

Open System

,

Shared Key

, or

Auto

.

°

In the open system, the wireless client can directly connect to the device

°

In the encryption authentication, the wireless client connects to the

modem through the shared key.

Data Rate

Choose the transmission rate of the wireless data.

You can choose

Auto

,

1 M

,

2 M

,

5.5 M

,

11 M

,

6 M

,

9 M

,

12 M

,

18 M

,

24 M

,

36

M

,

48

M

,

54M, MSC0 ~ MSC7.

PreambleType

°

Long Preamble

: It means this card always use long preamble.

°

Short Preamble

: It means this card can support short preamble

capability.

Broadcast SSID

Select whether the modem broadcasts SSID or not. You can select

Enable

or

Disable

.

°

Select

Enable

, the wireless client searches the modem through

broadcasting SSID.

°

Select

Disable

to hide SSID, the wireless clients can not find the SSID.

Relay Blocking

Wireless isolation. Select

Enable

, the wireless clients that are connected to

the modem can not intercommunication.

Ethernet to Wireless Blocking

Whether the wireless network can communicate with the Ethernet network or

not.

Wifi Multicast to Unicast

Enable it to using unicast to transmit multicast packet

Aggregation

It is applied when the destination end of all MPDU are for one STA.

Short GI

It is not recommended to enable GI in obvious environment of Multi-path

effect.

Apply Changes

Click it to apply the settings temporarily. If you want to save the settings of

this page permanently, click

Save

in the lower left corner.

3.4.3.6 WPS

Choose

WLAN

>

WPS

and the following page appears.

38

Page 44 / 73

802.11n Wireless ADSL2/2+ Router

ADN-4101

39

There are two ways for the wireless client to establish connection with the modem through WPS. Click

Regenerate

to generate a new PIN, and then click

Start PBC

, in the wireless client tool, enter the PIN which is generated by

the modem

，

start connection. The client will automatically establish the connection with the modem through the

encryption mode, and you need not to enter the key. The other way is the wireless client generates PIN. In the above

figure, enter PIN of the wireless client in the

Client PIN Number

field, then click

Start PIN

to establish the connection.

The wireless client establishes the connection with the modem through WPS

negotiation. The wireless client must support WPS.

Page 45 / 73

802.11n Wireless ADSL2/2+ Router

ADN-4101

3.4.3.7 WDS

Choose

WLAN

>

WDS

and the following page appears. On this page you can enable wireless distribution system

(WDS) so that the router can communicate with another AP.

The following table describes the parameters on this page:

Field

Description

MAC Address

Wireless MAC address of the AP to be connected

Comment

Add comment for the WDS AP

3.4.3.8 WDS Security

Choose

WLAN

>

WDS Security

and the following page appears. On this page, you can set up wireless security for

WDS.

The following table describes the parameters on this page:

Field

Description

Encryption

Choose a WDS encryption algorithm from

None

,

WEP

,

TKIP

or

AES

.

Pre-shared Key

Enter an encryption key.

40

Rate

Popular Planet Models

Famous Router IPs

Famous Router Companies

Bookmark Our Site

Share