Page 66 / 73
Scroll up to view Page 61 - 65
802.11n Wireless ADSL2/2+ Router
ADN-4101
Caution:
Do not turn off the router or press the Reset button while the procedure is in progress.
3.7.2.1 Upgrade Firmware
Click
Upgrade Firmware
in the left pane and the page shown in the following figure appears. On this page, you can
upgrade the firmware of the router.
The following table describes the parameters and button on this page:
Field
Description
Select File
Click
Browse
to select the firmware file.
Upload
After selecting the firmware file, click
Upload
to starting upgrading the firmware file.
Reset
Click it to starting selecting the firmware file.
3.7.2.2 Backup/Restore
Click
Backup/Restore
in the left pane and the page shown in the following figure appears. You can back up the
current settings to a file and restore the settings from the file that was saved previously.
The following table describes the parameters and button on this page:
Field
Description
Save Settings to File
Click it, and select the path. Then you can save the configuration file of
the router.
Load Settings from File
Click
Browse
to select the configuration file.
Upload
After selecting the configuration file of the router, click
Upload
to start
uploading the configuration file of the router.
61
Page 67 / 73
802.11n Wireless ADSL2/2+ Router
ADN-4101
3.7.3 Log
Choose
Admin
>
Log
and the page shown in the following figure appears. On this page, you can enable or disable
system log function and view the system log.
3.7.4 Password
Choose
Admin
>
Password
and the page shown in the following figure appears. By default, the user name and
password of the administrator are
admin
and
admin
respectively. The user name and password of the common user
are
user
and
user
respectively.
The following table describes the parameters on this page:
Field
Description
User Name
Choose the user name for accessing the router. You can choose
admin
or
user
.
Privilege
Choose the privilege for the account.
Old Password
Enter the old password
New Password
Enter the password to which you want to change the old password.
Confirm Password
Enter the new password again.
62
Page 68 / 73
802.11n Wireless ADSL2/2+ Router
ADN-4101
3.7.5 Time
Choose
Admin
>
Time
and the page shown in the following figure appears. You can configure the system time
manually or get the system time from the time server.
The following table describes the parameters on this page:
Field
Description
System Time
Set the system time manually.
NTP Configuration
State
Select enable or disable NTP function. You need to enable NTP if you want to
configure the parameters of NTP.
Server
Set the primary NTP server manually.
Server 2
Set the secondary NTP server manually.
Time Zone
Choose the time zone in which area you are from the drop down list.
3.8 Diagnostic
In the navigation bar, click
Diagnostic
. The
Diagnostic
page displayed contains
Ping
,
Traceroute
,
OAM Loopback
,
ADSL Statistics
and
Diag-Test
.
3.8.1 Ping
Choose
Diagnostic
>
Ping
and the page shown in the following figure appears.
The following table describes the parameter and button on this page:
Field
Description
Host
Enter the valid IP address or domain name.
Ping
Click it to start to Ping.
63
Page 69 / 73
802.11n Wireless ADSL2/2+ Router
ADN-4101
3.8.2 Traceroute
Choose
Diagnostic
>
Traceroute
and the following page appears. By Traceroute Diagnostic, you can track the route
path through the information which is from your computer to the Internet other side host.
The following table describes the parameters and buttons on this page.
Field
Description
Host
Enter the destination host address for diagnosis.
NumberOfTries
Number of repetitions.
Timeout
Put in the timeout value.
Datasize
Packet size.
DSCP
Differentiated Services Code Point, You should set a value between
0-63.
MaxHopCount
Maximum number of routes.
Interface
Select the interface.
Traceroute
Click start traceroute.
3.8.3 OAM Loopback
Choose
Diagnostic
>
OAM Loopback
and the page shown in the following figure appears. On this page, you can
use VCC loopback function to check the connectivity of the VCC. The ATM loopback test is useful for troubleshooting
problems with the DSLAM and ATM network.
Click
Go!
to start testing.
64
Page 70 / 73
802.11n Wireless ADSL2/2+ Router
ADN-4101
3.8.4 ADSL Statistics
Choose
Diagnostic
>
ADSL
Statistics
and the page shown in the following figure appears. It is used for ADSL tone
diagnostics.
Click
Start
to start ADSL tone diagnostics.
3.8.5 Diag-Test
Choose
Diagnostic
>
Diag-Test
and the page shown in the following figure appears. On this page, you can test the
DSL connection. You can also view the LAN status connection and ADSL connection.
Click
Run Diagnostic Test
to start testing.
65
19216811.live