Page 16 / 149
Scroll up to view Page 11 - 15
DISCUS™ Multiplay Wireless VoIP AG
10
(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
OGU 930500105-A1
Introduction
Page 17 / 149
Hardware Installation
(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
11
OGU 930500105-A1
Hardware
Installation
INTRODUCTION
This chapter will guide you through a basic installation of the Router
including:
1.
Positioning the
DISCUS™ Multiplay Wireless VoIP AG
2.
Installing Micro Filters
3.
Connecting the Router to your network
4.
Setting up your computer for networking with the Router
POSITIONING THE ROUTER
You should place the Router in such a location to ensure that:
•
It is located near an electrical outlet and a phone wall socket
•
Water or moisture cannot enter the case of the unit
•
It is out of direct sunlight and away from sources of heat
•
The cabling is away from power lines, fluorescent lighting fixtures,
and sources of electrical noise such as radios, transmitters and
broadband amplifiers.
Please read carefully the Safety Information in Appendix “A”
A multimedia guided tour on how to connect your device and install the router’s drivers is
available on CD-ROM. It is recommended to follow CD-ROM procedures to easy up device
setup.
Page 18 / 149
DISCUS™ Multiplay Wireless VoIP AG
(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
12
OGU 930500105-A1
Hardware Installation
•
It is centrally located to the wireless computers that will connect to the
Router. A suitable location might be on top of a high shelf to optimize wire-
less connections to computers in both horizontal and vertical directions,
allowing wider coverage
INSTALLING MICRO
FILTERS
Before beginning installation you must locate devices in your house requiring a
DSL filter such as phones, fax machines, answering machines, dial-up
modems, Satellite TV dialers or monitored security systems and attach a DSL
filter to any one of them sharing the same phone line as your DSL modem.
To install DSL filters please follow these steps:
1.
Disconnect the phone cable from the telephone wall socket
2.
Insert the phone cable into the DSL filter socket identified with a phone
symbol
3.
Insert the DSL filter cable into the telephone wall socket
FIGURE 1.
Micro Filter Installation
You do not need to attach a DSL filter to unused wall sockets.
1
2
3
Page 19 / 149
DISCUS™ Multiplay Wireless VoIP AG
(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
13
OGU 930500105-A1
Hardware Installation
POWERING UP THE
ROUTER
To power up the Router:
1.
Plug the power adapter into the power adapter socket located on the rear
panel of the Router
2.
Plug the power adapter into a standard electrical wall socket
3.
Wait for the power LED to turn steady green
CONNECTING THE ROUTER
The first step to install the router is to physically connect it to the telephone
socket and then to connect it to a computer - by means of an Ethernet or an
USB connection - to be able to access the Internet
To connect the phone cable:
1.
Connect one end of the phone cable into the DSL filter socket identified with
a computer symbol
2.
Connect the other end of the phone cable into the DSL socket of the Router
FIGURE 2.
Phone Cable Connection
To connect the Ethernet cable:
Page 20 / 149
DISCUS™ Multiplay Wireless VoIP AG
(C) (2006) Pirelli Broadband Solutions S.p.A. All Rights Reserved. Proprietary Use Pursuant to Cover Page Instructions.
14
OGU 930500105-A1
Hardware Installation
1.
Connect one end of the Ethernet cable into one of the four Ethernet sockets
on the rear of the Router
2.
Connect the other end of the ethernet cable into the Ethernet plug of your
computer
FIGURE 3.
Ethernet Cable Connection
To connect the USB cable:
1.
Connect one end of the USB cable into the USB socket on the rear of the
Router.
19216811.live