Page 21 / 26 Scroll up to view Page 16 - 20
PePWave Surf (AP) / Surf DX /
Mesh Connector / CarFi Series
- 21 -
Copyright © 2008 PePWave
PePWave User Manual
4.6
Test the Setup
To test to setup, you can now go to the unit’s main page, enter the user name and
password.
The realm (the text box next to the “@” sign) value can be left empty.
Then
click the Connect button.
Illustration 14: Establishing Connection to the Internet
After connected, you should see:
Illustration 15: Internet Connection Established
Page 22 / 26
PePWave Surf (AP) / Surf DX /
Mesh Connector / CarFi Series
- 22 -
Copyright © 2008 PePWave
PePWave User Manual
4.7
Post-configuring PC Setup for Mesh Connector Series
At this point an Internet connection should have been successfully established between the
access point and the PePWave Mesh Connector. The PC that was previously pre-configured
to administrate the Surf has to reconfigure its Local Area Connection and be set to ‘Obtain
an IP address automatically’.
An ‘Internet Protocol (TCP/IP) Properties’ screen will appear. Please set as follows:
Click the “OK” button to confirm the change.
For now the PC will send a DHCP request directly to the access point via the PePWave Mesh
Connector, and an IP address will be assigned from the access point to the PC.
4.8
Firmware Upgrade
The PePWave devices (Surf / Surf DX / Mesh Connector / CarFi Series) are able to check
whether a newer firmware (the software running on the unit) is available.
This can be done
in the Firmware Upgrade section.
However, it is recommended that you do not update the firmware unless specifically
instructed by your ISP to do so.
When a firmware upgrade is needed, your ISP will either
give you instructions or upgrade the firmware remotely.
Page 23 / 26
PePWave Surf (AP) / Surf DX /
Mesh Connector / CarFi Series
- 23 -
Copyright © 2008 PePWave
PePWave User Manual
4.9
Restore to Default Settings
4.9.1 Surf Indoor Series
There are two ways to restore the PePWave Surf Indoor unit to default settings.
If you are able to access the web admin interface, go to the “CPE Setup” page, and click the
Restore and Reboot
button.
Otherwise, you can also power up the unit and wait for about 1 min.
Then press the
Reset
Button
at the rear side of the unit using a pin and then hold it for 5 seconds.
The unit will
restore the settings to factory default and reboot.
4.9.2 Surf DX Series
There are two ways to restore the PePWave Surf DX to default settings.
If you are able to access the web admin interface, go to the “CPE Setup” page, and click the
Restore and Reboot
button.
Otherwise, you can also power up the Surf DX unit and wait for about 1 min.
Then push the
Reset Button
at the panel side of the unit and then hold it for 5 seconds.
The unit will
restore the settings to factory default and reboot.
4.9.3 Surf AP Outdoor / Mesh Connector Outdoor Series
There are two ways to restore the PePWave Surf AP outdoor/ Mesh Connector outdoor
device to default settings.
If you are able to access the web admin interface, go to the “CPE Setup” page, and click the
Restore and Reboot
button.
Page 24 / 26
PePWave Surf (AP) / Surf DX /
Mesh Connector / CarFi Series
- 24 -
Copyright © 2008 PePWave
PePWave User Manual
Otherwise, you need to open the cover of the outdoor device and also power up the device
and wait for about 1 min.
Then push the
Reset Button
(see the illustration blow) and then
hold it for 5 seconds.
The device will restore the settings to factory default and reboot.
4.9.4 Mesh Connector Indoor / CarFi Series
There are two ways to restore the PePWave Mesh Connector Indoor or the CarFi unit to
default settings.
If you are able to access the web admin interface, go to the “CPE Setup” page, and click the
Restore and Reboot
button.
Otherwise, you can also power up the unit and wait for about 1 min.
Then push the
Reset
Button
at the rear side of the unit using a pin and then hold it for 5 seconds.
The unit will
restore the settings to factory default and reboot.
Page 25 / 26
PePWave Surf (AP) / Surf DX /
Mesh Connector / CarFi Series
- 25 -
Copyright © 2008 PePWave
PePWave User Manual
Appendix:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.

Rate

3.5 / 5 based on 2 votes.

Popular Pepwave Models

Bookmark Our Site

Press Ctrl + D to add this site to your favorites!

Share
Top