Page 41 / 116
Scroll up to view Page 36 - 40
SETUP WIZARD
4-3
SETUP WIZARD
Channel and SSID
Click on “SETUP WIZARD” and “NEXT”, then you will see the Channel
and SSID page.
Click “NEXT” to continue.
Parameter
Description
ESSID
Extended Service Set ID. The ESSID must be the same on the
ADSL Router and all of its wireless clients.
ESSID Broadcast
Enable or disable the broadcasting of the SSID.
Wireless Mode
This device supports both 11g and 11b wireless networks. Make
your selection depending on the type of wireless network that
you have.
Channel
The radio channel used by the wireless router and its clients to
communicate with each other. This channel must be the same
on the ADSL Router and all of its wireless clients.
The ADSL Router will automatically assign itself a radio
channel, or you may select one manually.
Downloaded from
www.Manualslib.com
manuals search engine
Page 42 / 116
C
ONFIGURING
THE
ADSL R
OUTER
4-4
Parameter Setting
Select your Country and Internet Service Provider. This will automatically
configure the
ADSL Router
with the correct Protocol, Encapsulation and
VPI/VCI settings for your ISP.
If your Country or Internet Service Provider is not listed you will need to
manually enter settings. Go to “Parameter Setting - Country or ISP Not
Listed” on page 4-7 in the manual.
If your ISP uses PPPoA or PPPoE, then you will need to enter the
username, password and DNS Server address supplied by your ISP.
If your ISP uses 1483 Routing, then you will need to enter the IP address,
Subnet Mask, Default Gateway and DNS Server address supplied by your
ISP.
Note:
By default
192.168.2.1 is set for the DNS Server address, this
needs to be changed to reflect your ISP’s DNS Server address.
Click “NEXT” to continue.
Downloaded from
www.Manualslib.com
manuals search engine
Page 43 / 116
SETUP WIZARD
4-5
Confirm
The Confirm page shows a summary of the configuration parameters.
Check ADSL operation mode (WAN), Network Layer Parameters (WAN)
and DHCP parameters are correct.
Parameter
Description
ADSL Operation Mode
(WAN)
ISP
The type of ISP you have selected.
Protocol
Indicates the protocol used.
VPI/VCI
Virtual Path Identifier (VPI) and Virtual Circuit Identifier
(VCI).
AAL5 Encapsulation
Shows the packet encapsulation type. Go to
page 4-20 for
a detailed description.
Network Layer
Parameters (WAN)
IP Address
WAN IP address.
Subnet Mask
WAN subnet mask.
Default Gateway
WAN gateway.
Downloaded from
www.Manualslib.com
manuals search engine
Page 44 / 116
C
ONFIGURING
THE
ADSL R
OUTER
4-6
If the parameters are correct, click “NEXT” to save these settings.
DHCP Parameters
Function
Shows the DHCP function is enabled or disabled.
Default Gateway
LAN IP address of the ADSL Router.
Subnet Mask
The network subnet mask.
Name Server 1
Primary DNS server IP address.
Name Server 2
Alternate DNS server IP address.
Start IP Address
Start IP address of DHCP assigned IP addresses.
Number of IP
Number of IP addresses available for assignment by the
DHCP server.
Parameter
Description
Downloaded from
www.Manualslib.com
manuals search engine
Page 45 / 116
SETUP WIZARD
4-7
Parameter Setting - Country or ISP Not Listed
If your Country or Internet Service Provider is not listed on the drop
down menu, select “Others”. This will allow you to manually configure
your ISP settings.
For manual configuration you will need to know the Protocol, DNS
Server, Encapsulation and VPI/VCI settings used by your ISP. If you have
a Static IP address you will also need to know the IP address, Subnet Mask
and Gateway address. Please contact your ISP for these details if you do
not already have them.
After selecting “Others” you will be required to select what Protocol your
ISP uses from the “Internet Service Provider” drop down list.
Downloaded from
www.Manualslib.com
manuals search engine
19216811.live