Page 16 / 88
Scroll up to view Page 11 - 15
11
Using the Device for the First Time
To get started, follow these steps:
➊
Confirm your computer meets the minimum system requirements. (See
System
Requirements
on page 3.)
➋
Assemble the wall charger. (See
Assemble the Wall Charger
on page 12.)
➌
Install the 4G LTE SIM Card. (See
Install the 4G LTE SIM Card
on page 12.)
➍
Insert and charge the battery. (See
Insert and Charge the Battery
on page 14.)
➎
Turn on the device. (See
Power the MiFi 4510L On and Off
on page 18.)
➏
Connect the device to your computer using Wi-Fi. (See
Connecting to the MiFi Device
on
page 19.)
➐
Connect to MiFi Settings. (See
Connect to MiFi Settings
on page 19.)
IMPORTANT
The MiFi 4510L requires an activated account with a network operator to
function.
Page 17 / 88
12
Assemble the Wall Charger
The wall charger comes with a removable plug. You need to connect it before using the MiFi device
for the first time. To assemble the wall charger, follow these steps:
➊
Remove the plug and the wall charger from the package.
➋
Slide the plug into the wall charger.
Install the 4G LTE SIM Card
To install your new 4G SIM Card, follow these steps:
➊
Open the cover located on the underside of the MiFi 4510L.
➋
Remove SIM Card from the outer card, being careful not to touch the gold-colored contacts.
➌
Hold the card as shown, with the gold-colored contact points facing down.
➍
Insert the SIM Card into the slot. The 4G LTE SIM Card MUST remain in the SIM Card slot when
in use.
Your SIM (Subscriber Identity Module) card is a small rectangular plastic card that stores your phone
number and important information about your wireless service.
CAUTION!
Do not bend or scratch your SIM Card. Avoid exposing your SIM Card to static
electricity, water, or dirt.
Page 18 / 88
13
Remove the 4G LTE SIM Card
To remove the 4G LTE SIM Card, follow these steps:
➊
Open the SIM Card cover located on the underside of the MiFi 4510L. Press down on the
small black tab to the left side of the SIM Card slot.
➋
Gently remove the SIM Card from the SIM Card slot.
NOTE
Should your 4G LTE SIM Card be lost or damaged, contact your network operator.
Page 19 / 88
14
Insert and Charge the Battery
IMPORTANT
Before you use your device, be sure to charge the battery for at least three hours
to ensure a full initial charge.
To insert and charge the battery, follow these steps:
➊
Press the button and then slide the cover to open the battery compartment, located on the
bottom of the device. Set the cover aside.
➋
Align the gold-colored contacts on the battery with the gold-colored contacts on the device
and gently slide the battery into place.
Page 20 / 88
15
➌
Replace the cover by setting it on the device where the notches align, and then gently slide
the cover back toward the release button until it clicks into place.
➍
Connect the micro USB end of the wall charger to the micro USB port on the device.
IMPORTANT
When connecting the MiFi 4510L to your computer, it is recommended that a
good quality shielded USB cable that is equal to or less than 1 m (~3'3") in length be used.
➎
Plug the other end of the wall charger into the appropriate electrical outlet. Charge for at
least three hours.
WARNING !
Use only batteries and chargers with your device that have been approved by
Verizon Wireless. The failure to use approved batteries and chargers may increase the risk that
your device will overheat, catch fire, or explode, resulting in serious bodily injury, death, or
property damage.
You are now ready to connect your computer or other Wi-Fi enabled device to the MiFi 4510L.
19216811.live